Abstract

Transparent aluminium oxynitride (AlON) ceramics were prepared by hot isostatic pressing (HIP) with 0.08~0.14 wt% Y2O3 or 0.01~0.04 wt% La2O3 as sintering additives. Both Y2O3 and La2O3 additives prompted sintering process and accelerated grain growth. When higher amount of Y2O3 (0.12 wt%) or La2O3 (0.03 wt%) additives were doped, extensive twins occurred accompanied with the coarsing of grain size (~100μm). Electron backscatter diffraction (EBSD) analysis showed that twin boundaries increased with the increasing of Y2O3/La2O3 concentrations. By co-doping of Y2O3 -La2O3 additives with reduced doping level, the formation of twins was successfully suppressed, which was necessary to limit the additional light scattering of twin boundaries.

© 2015 Optical Society of America

Full Article  |  PDF Article
OSA Recommended Articles
Post-sintering treatment of neodymium-doped yttrium aluminum garnet (Nd:YAG) transparent ceramics

Lucie Chrétien, Rémy Boulesteix, Alexandre Maître, Christian Sallé, and Yves Reignoux
Opt. Mater. Express 4(10) 2166-2173 (2014)

Improvement of optical properties and suppression of second phase exsolution by doping fluorides in Y3Al5O12 transparent ceramics

Jintai Fan, Siyuan Chen, Benxue Jiang, Liangjie Pan, Yang Zhang, Xiaojian Mao, Xinqiang Yuan, Rihong Li, Xiongwei Jiang, and Long Zhang
Opt. Mater. Express 4(9) 1800-1806 (2014)

Two-step sintering of Gd0.3Lu1.6Eu0.1O3 transparent ceramic scintillator

Zachary Seeley, Nerine Cherepy, and Stephen Payne
Opt. Mater. Express 3(7) 908-912 (2013)

References

  • View by:
  • |
  • |
  • |

  1. R. M. Sullivan, “A historical view of AlON,” Proc. SPIE 5786, 23–32 (2005).
    [Crossref]
  2. J. W. McCauley, P. Patel, M. W. Chen, G. Gilde, E. Strassburger, B. Paliwal, K. T. Ramesh, and D. P. Dandekar, “AlON: A brief history of its emergence and evolution,” J. Eur. Ceram. Soc. 29(2), 223–236 (2009).
    [Crossref]
  3. C. T. Warner, T. M. Hartnett, D. Fisher, and W. Sunne, “Characterization of AlON optical ceramic,” Proc. SPIE 5786, 95–111 (2005).
    [Crossref]
  4. R. Apetz and M. P. B. V. Bruggen, “Transparent alumina: A light-scattering model,” J. Am. Ceram. Soc. 86(3), 480–486 (2003).
    [Crossref]
  5. J. Wang, F. Zhang, F. Chen, J. Zhang, H. L. Zhang, R. Tian, Z. J. Wang, and S. W. Wang, “Effect of Y2O3 and La2O3 on the sinterability of γ-AlON transparent ceramic,” J. Eur. Ceram. Soc. 35(1), 23–28 (2015).
    [Crossref]
  6. D. Clay, D. Poslusny, M. Flinders, S. D. Jacobs, and R. A. Cutler, “Effect of LiAl5O8 additions on the sintering and optical transparency of LiAlON,” J. Eur. Ceram. Soc. 26(8), 1351–1362 (2006).
    [Crossref]
  7. T. M. Hartnett, S. D. Bernstein, E. A. Maguire, and R. W. Tustison, “Optical properties of ALON aluminum oxynitride,” Infrared Phys. Technol. 39(4), 203–211 (1998).
    [Crossref]
  8. F. Chen, F. Zhang, J. Wang, H. L. Zhang, R. Tian, J. Zhang, Z. Zhang, F. Sun, and S. W. Wang, “Microstructure and optical properties of transparent aluminum oxynitride ceramics by hot isostatic pressing,” Scr. Mater. 81, 20–23 (2014).
    [Crossref]
  9. L. Lu, X. Chen, X. Huang, and K. Lu, “Revealing the maximum strength in nanotwinned copper,” Science 323(5914), 607–610 (2009).
    [Crossref] [PubMed]
  10. J. L. Bair, S. L. Hatch, and D. P. Field, “Formation of annealing twin boundaries in nickel,” Scr. Mater. 81, 52–55 (2014).
    [Crossref]
  11. J. R. Luo, A. Godfrey, W. Liu, and Q. Liu, “Twinning behavior of a strongly basal textured AZ31Mg alloy during warm rolling,” Acta Mater. 60(5), 1986–1998 (2012).
    [Crossref]
  12. M. Wei, D. Zhi, and D. G. Brandon, “Microstructure and texture evolution in gel-cast α-alumina/alumina platelet ceramic composites,” Scr. Mater. 53(12), 1327–1332 (2005).
    [Crossref]
  13. P. Vonlanthen and B. Grobety, “CSL grain boundary distribution in alumina and zirconia ceramics,” Ceram. Int. 34(6), 1459–1472 (2008).
    [Crossref]
  14. S. N. Perevislov, V. D. Chupov, S. S. Ordan’yan, and M. V. Tomkovich, “Obtaining high-density silicon carbide materials by liquid-phase sintering in the system SiC–Al2O3–Y2O3–MgO,” Ogneup. Tekh. Keram 4–5, 26–32 (2011).
  15. S. H. Lee, E. R. Kupp, A. J. Stevenson, J. M. Anderson, G. L. Messing, X. Li, E. C. Dickey, J. Q. Dumm, V. K. Simonaitis-Castillo, and G. J. Quarles, “Hot isostatic pressing of transparent Nd:YAG ceramics,” J. Am. Ceram. Soc. 92(7), 1456–1463 (2009).
    [Crossref]
  16. W. Wang, S. L. Korinek, F. Brisset, A. L. Helbert, J. Bourgon, and T. Baudin, “Formation of annealing twins during primary recrystallization of two low stacking fault energy Ni-based alloys,” J. Mater. Sci. 50(5), 2167–2177 (2015).
    [Crossref]
  17. C. S. Pande, M. A. Imam, and B. B. Rath, “Study of annealing twins in FCC metals and alloys,” Met.Trans.A. 21(11), 2891–2896 (1990).
    [Crossref]
  18. S. Dash and N. Brown, “An investigation of the origin and growth of annealing twins,” Acta Metall. 11(9), 1067–1075 (1963).
    [Crossref]
  19. L. Miller and W. D. Kaplan, “Solubility limits of La and Y in aluminum oxynitride at 1870°C,” J. Am. Ceram. Soc. 91(5), 1693–1696 (2008).
    [Crossref]
  20. A. Krell, T. Hutzler, J. Klimke, and A. Potthoff, “Fine-Grained Transparent spinel windows by the processing of different nanopowders,” J. Am. Ceram. Soc. 93(9), 2656–2666 (2010).
    [Crossref]

2015 (2)

J. Wang, F. Zhang, F. Chen, J. Zhang, H. L. Zhang, R. Tian, Z. J. Wang, and S. W. Wang, “Effect of Y2O3 and La2O3 on the sinterability of γ-AlON transparent ceramic,” J. Eur. Ceram. Soc. 35(1), 23–28 (2015).
[Crossref]

W. Wang, S. L. Korinek, F. Brisset, A. L. Helbert, J. Bourgon, and T. Baudin, “Formation of annealing twins during primary recrystallization of two low stacking fault energy Ni-based alloys,” J. Mater. Sci. 50(5), 2167–2177 (2015).
[Crossref]

2014 (2)

F. Chen, F. Zhang, J. Wang, H. L. Zhang, R. Tian, J. Zhang, Z. Zhang, F. Sun, and S. W. Wang, “Microstructure and optical properties of transparent aluminum oxynitride ceramics by hot isostatic pressing,” Scr. Mater. 81, 20–23 (2014).
[Crossref]

J. L. Bair, S. L. Hatch, and D. P. Field, “Formation of annealing twin boundaries in nickel,” Scr. Mater. 81, 52–55 (2014).
[Crossref]

2012 (1)

J. R. Luo, A. Godfrey, W. Liu, and Q. Liu, “Twinning behavior of a strongly basal textured AZ31Mg alloy during warm rolling,” Acta Mater. 60(5), 1986–1998 (2012).
[Crossref]

2011 (1)

S. N. Perevislov, V. D. Chupov, S. S. Ordan’yan, and M. V. Tomkovich, “Obtaining high-density silicon carbide materials by liquid-phase sintering in the system SiC–Al2O3–Y2O3–MgO,” Ogneup. Tekh. Keram 4–5, 26–32 (2011).

2010 (1)

A. Krell, T. Hutzler, J. Klimke, and A. Potthoff, “Fine-Grained Transparent spinel windows by the processing of different nanopowders,” J. Am. Ceram. Soc. 93(9), 2656–2666 (2010).
[Crossref]

2009 (3)

S. H. Lee, E. R. Kupp, A. J. Stevenson, J. M. Anderson, G. L. Messing, X. Li, E. C. Dickey, J. Q. Dumm, V. K. Simonaitis-Castillo, and G. J. Quarles, “Hot isostatic pressing of transparent Nd:YAG ceramics,” J. Am. Ceram. Soc. 92(7), 1456–1463 (2009).
[Crossref]

L. Lu, X. Chen, X. Huang, and K. Lu, “Revealing the maximum strength in nanotwinned copper,” Science 323(5914), 607–610 (2009).
[Crossref] [PubMed]

J. W. McCauley, P. Patel, M. W. Chen, G. Gilde, E. Strassburger, B. Paliwal, K. T. Ramesh, and D. P. Dandekar, “AlON: A brief history of its emergence and evolution,” J. Eur. Ceram. Soc. 29(2), 223–236 (2009).
[Crossref]

2008 (2)

P. Vonlanthen and B. Grobety, “CSL grain boundary distribution in alumina and zirconia ceramics,” Ceram. Int. 34(6), 1459–1472 (2008).
[Crossref]

L. Miller and W. D. Kaplan, “Solubility limits of La and Y in aluminum oxynitride at 1870°C,” J. Am. Ceram. Soc. 91(5), 1693–1696 (2008).
[Crossref]

2006 (1)

D. Clay, D. Poslusny, M. Flinders, S. D. Jacobs, and R. A. Cutler, “Effect of LiAl5O8 additions on the sintering and optical transparency of LiAlON,” J. Eur. Ceram. Soc. 26(8), 1351–1362 (2006).
[Crossref]

2005 (3)

C. T. Warner, T. M. Hartnett, D. Fisher, and W. Sunne, “Characterization of AlON optical ceramic,” Proc. SPIE 5786, 95–111 (2005).
[Crossref]

M. Wei, D. Zhi, and D. G. Brandon, “Microstructure and texture evolution in gel-cast α-alumina/alumina platelet ceramic composites,” Scr. Mater. 53(12), 1327–1332 (2005).
[Crossref]

R. M. Sullivan, “A historical view of AlON,” Proc. SPIE 5786, 23–32 (2005).
[Crossref]

2003 (1)

R. Apetz and M. P. B. V. Bruggen, “Transparent alumina: A light-scattering model,” J. Am. Ceram. Soc. 86(3), 480–486 (2003).
[Crossref]

1998 (1)

T. M. Hartnett, S. D. Bernstein, E. A. Maguire, and R. W. Tustison, “Optical properties of ALON aluminum oxynitride,” Infrared Phys. Technol. 39(4), 203–211 (1998).
[Crossref]

1990 (1)

C. S. Pande, M. A. Imam, and B. B. Rath, “Study of annealing twins in FCC metals and alloys,” Met.Trans.A. 21(11), 2891–2896 (1990).
[Crossref]

1963 (1)

S. Dash and N. Brown, “An investigation of the origin and growth of annealing twins,” Acta Metall. 11(9), 1067–1075 (1963).
[Crossref]

Anderson, J. M.

S. H. Lee, E. R. Kupp, A. J. Stevenson, J. M. Anderson, G. L. Messing, X. Li, E. C. Dickey, J. Q. Dumm, V. K. Simonaitis-Castillo, and G. J. Quarles, “Hot isostatic pressing of transparent Nd:YAG ceramics,” J. Am. Ceram. Soc. 92(7), 1456–1463 (2009).
[Crossref]

Apetz, R.

R. Apetz and M. P. B. V. Bruggen, “Transparent alumina: A light-scattering model,” J. Am. Ceram. Soc. 86(3), 480–486 (2003).
[Crossref]

Bair, J. L.

J. L. Bair, S. L. Hatch, and D. P. Field, “Formation of annealing twin boundaries in nickel,” Scr. Mater. 81, 52–55 (2014).
[Crossref]

Baudin, T.

W. Wang, S. L. Korinek, F. Brisset, A. L. Helbert, J. Bourgon, and T. Baudin, “Formation of annealing twins during primary recrystallization of two low stacking fault energy Ni-based alloys,” J. Mater. Sci. 50(5), 2167–2177 (2015).
[Crossref]

Bernstein, S. D.

T. M. Hartnett, S. D. Bernstein, E. A. Maguire, and R. W. Tustison, “Optical properties of ALON aluminum oxynitride,” Infrared Phys. Technol. 39(4), 203–211 (1998).
[Crossref]

Bourgon, J.

W. Wang, S. L. Korinek, F. Brisset, A. L. Helbert, J. Bourgon, and T. Baudin, “Formation of annealing twins during primary recrystallization of two low stacking fault energy Ni-based alloys,” J. Mater. Sci. 50(5), 2167–2177 (2015).
[Crossref]

Brandon, D. G.

M. Wei, D. Zhi, and D. G. Brandon, “Microstructure and texture evolution in gel-cast α-alumina/alumina platelet ceramic composites,” Scr. Mater. 53(12), 1327–1332 (2005).
[Crossref]

Brisset, F.

W. Wang, S. L. Korinek, F. Brisset, A. L. Helbert, J. Bourgon, and T. Baudin, “Formation of annealing twins during primary recrystallization of two low stacking fault energy Ni-based alloys,” J. Mater. Sci. 50(5), 2167–2177 (2015).
[Crossref]

Brown, N.

S. Dash and N. Brown, “An investigation of the origin and growth of annealing twins,” Acta Metall. 11(9), 1067–1075 (1963).
[Crossref]

Bruggen, M. P. B. V.

R. Apetz and M. P. B. V. Bruggen, “Transparent alumina: A light-scattering model,” J. Am. Ceram. Soc. 86(3), 480–486 (2003).
[Crossref]

Chen, F.

J. Wang, F. Zhang, F. Chen, J. Zhang, H. L. Zhang, R. Tian, Z. J. Wang, and S. W. Wang, “Effect of Y2O3 and La2O3 on the sinterability of γ-AlON transparent ceramic,” J. Eur. Ceram. Soc. 35(1), 23–28 (2015).
[Crossref]

F. Chen, F. Zhang, J. Wang, H. L. Zhang, R. Tian, J. Zhang, Z. Zhang, F. Sun, and S. W. Wang, “Microstructure and optical properties of transparent aluminum oxynitride ceramics by hot isostatic pressing,” Scr. Mater. 81, 20–23 (2014).
[Crossref]

Chen, M. W.

J. W. McCauley, P. Patel, M. W. Chen, G. Gilde, E. Strassburger, B. Paliwal, K. T. Ramesh, and D. P. Dandekar, “AlON: A brief history of its emergence and evolution,” J. Eur. Ceram. Soc. 29(2), 223–236 (2009).
[Crossref]

Chen, X.

L. Lu, X. Chen, X. Huang, and K. Lu, “Revealing the maximum strength in nanotwinned copper,” Science 323(5914), 607–610 (2009).
[Crossref] [PubMed]

Chupov, V. D.

S. N. Perevislov, V. D. Chupov, S. S. Ordan’yan, and M. V. Tomkovich, “Obtaining high-density silicon carbide materials by liquid-phase sintering in the system SiC–Al2O3–Y2O3–MgO,” Ogneup. Tekh. Keram 4–5, 26–32 (2011).

Clay, D.

D. Clay, D. Poslusny, M. Flinders, S. D. Jacobs, and R. A. Cutler, “Effect of LiAl5O8 additions on the sintering and optical transparency of LiAlON,” J. Eur. Ceram. Soc. 26(8), 1351–1362 (2006).
[Crossref]

Cutler, R. A.

D. Clay, D. Poslusny, M. Flinders, S. D. Jacobs, and R. A. Cutler, “Effect of LiAl5O8 additions on the sintering and optical transparency of LiAlON,” J. Eur. Ceram. Soc. 26(8), 1351–1362 (2006).
[Crossref]

Dandekar, D. P.

J. W. McCauley, P. Patel, M. W. Chen, G. Gilde, E. Strassburger, B. Paliwal, K. T. Ramesh, and D. P. Dandekar, “AlON: A brief history of its emergence and evolution,” J. Eur. Ceram. Soc. 29(2), 223–236 (2009).
[Crossref]

Dash, S.

S. Dash and N. Brown, “An investigation of the origin and growth of annealing twins,” Acta Metall. 11(9), 1067–1075 (1963).
[Crossref]

Dickey, E. C.

S. H. Lee, E. R. Kupp, A. J. Stevenson, J. M. Anderson, G. L. Messing, X. Li, E. C. Dickey, J. Q. Dumm, V. K. Simonaitis-Castillo, and G. J. Quarles, “Hot isostatic pressing of transparent Nd:YAG ceramics,” J. Am. Ceram. Soc. 92(7), 1456–1463 (2009).
[Crossref]

Dumm, J. Q.

S. H. Lee, E. R. Kupp, A. J. Stevenson, J. M. Anderson, G. L. Messing, X. Li, E. C. Dickey, J. Q. Dumm, V. K. Simonaitis-Castillo, and G. J. Quarles, “Hot isostatic pressing of transparent Nd:YAG ceramics,” J. Am. Ceram. Soc. 92(7), 1456–1463 (2009).
[Crossref]

Field, D. P.

J. L. Bair, S. L. Hatch, and D. P. Field, “Formation of annealing twin boundaries in nickel,” Scr. Mater. 81, 52–55 (2014).
[Crossref]

Fisher, D.

C. T. Warner, T. M. Hartnett, D. Fisher, and W. Sunne, “Characterization of AlON optical ceramic,” Proc. SPIE 5786, 95–111 (2005).
[Crossref]

Flinders, M.

D. Clay, D. Poslusny, M. Flinders, S. D. Jacobs, and R. A. Cutler, “Effect of LiAl5O8 additions on the sintering and optical transparency of LiAlON,” J. Eur. Ceram. Soc. 26(8), 1351–1362 (2006).
[Crossref]

Gilde, G.

J. W. McCauley, P. Patel, M. W. Chen, G. Gilde, E. Strassburger, B. Paliwal, K. T. Ramesh, and D. P. Dandekar, “AlON: A brief history of its emergence and evolution,” J. Eur. Ceram. Soc. 29(2), 223–236 (2009).
[Crossref]

Godfrey, A.

J. R. Luo, A. Godfrey, W. Liu, and Q. Liu, “Twinning behavior of a strongly basal textured AZ31Mg alloy during warm rolling,” Acta Mater. 60(5), 1986–1998 (2012).
[Crossref]

Grobety, B.

P. Vonlanthen and B. Grobety, “CSL grain boundary distribution in alumina and zirconia ceramics,” Ceram. Int. 34(6), 1459–1472 (2008).
[Crossref]

Hartnett, T. M.

C. T. Warner, T. M. Hartnett, D. Fisher, and W. Sunne, “Characterization of AlON optical ceramic,” Proc. SPIE 5786, 95–111 (2005).
[Crossref]

T. M. Hartnett, S. D. Bernstein, E. A. Maguire, and R. W. Tustison, “Optical properties of ALON aluminum oxynitride,” Infrared Phys. Technol. 39(4), 203–211 (1998).
[Crossref]

Hatch, S. L.

J. L. Bair, S. L. Hatch, and D. P. Field, “Formation of annealing twin boundaries in nickel,” Scr. Mater. 81, 52–55 (2014).
[Crossref]

Helbert, A. L.

W. Wang, S. L. Korinek, F. Brisset, A. L. Helbert, J. Bourgon, and T. Baudin, “Formation of annealing twins during primary recrystallization of two low stacking fault energy Ni-based alloys,” J. Mater. Sci. 50(5), 2167–2177 (2015).
[Crossref]

Huang, X.

L. Lu, X. Chen, X. Huang, and K. Lu, “Revealing the maximum strength in nanotwinned copper,” Science 323(5914), 607–610 (2009).
[Crossref] [PubMed]

Hutzler, T.

A. Krell, T. Hutzler, J. Klimke, and A. Potthoff, “Fine-Grained Transparent spinel windows by the processing of different nanopowders,” J. Am. Ceram. Soc. 93(9), 2656–2666 (2010).
[Crossref]

Imam, M. A.

C. S. Pande, M. A. Imam, and B. B. Rath, “Study of annealing twins in FCC metals and alloys,” Met.Trans.A. 21(11), 2891–2896 (1990).
[Crossref]

Jacobs, S. D.

D. Clay, D. Poslusny, M. Flinders, S. D. Jacobs, and R. A. Cutler, “Effect of LiAl5O8 additions on the sintering and optical transparency of LiAlON,” J. Eur. Ceram. Soc. 26(8), 1351–1362 (2006).
[Crossref]

Kaplan, W. D.

L. Miller and W. D. Kaplan, “Solubility limits of La and Y in aluminum oxynitride at 1870°C,” J. Am. Ceram. Soc. 91(5), 1693–1696 (2008).
[Crossref]

Klimke, J.

A. Krell, T. Hutzler, J. Klimke, and A. Potthoff, “Fine-Grained Transparent spinel windows by the processing of different nanopowders,” J. Am. Ceram. Soc. 93(9), 2656–2666 (2010).
[Crossref]

Korinek, S. L.

W. Wang, S. L. Korinek, F. Brisset, A. L. Helbert, J. Bourgon, and T. Baudin, “Formation of annealing twins during primary recrystallization of two low stacking fault energy Ni-based alloys,” J. Mater. Sci. 50(5), 2167–2177 (2015).
[Crossref]

Krell, A.

A. Krell, T. Hutzler, J. Klimke, and A. Potthoff, “Fine-Grained Transparent spinel windows by the processing of different nanopowders,” J. Am. Ceram. Soc. 93(9), 2656–2666 (2010).
[Crossref]

Kupp, E. R.

S. H. Lee, E. R. Kupp, A. J. Stevenson, J. M. Anderson, G. L. Messing, X. Li, E. C. Dickey, J. Q. Dumm, V. K. Simonaitis-Castillo, and G. J. Quarles, “Hot isostatic pressing of transparent Nd:YAG ceramics,” J. Am. Ceram. Soc. 92(7), 1456–1463 (2009).
[Crossref]

Lee, S. H.

S. H. Lee, E. R. Kupp, A. J. Stevenson, J. M. Anderson, G. L. Messing, X. Li, E. C. Dickey, J. Q. Dumm, V. K. Simonaitis-Castillo, and G. J. Quarles, “Hot isostatic pressing of transparent Nd:YAG ceramics,” J. Am. Ceram. Soc. 92(7), 1456–1463 (2009).
[Crossref]

Li, X.

S. H. Lee, E. R. Kupp, A. J. Stevenson, J. M. Anderson, G. L. Messing, X. Li, E. C. Dickey, J. Q. Dumm, V. K. Simonaitis-Castillo, and G. J. Quarles, “Hot isostatic pressing of transparent Nd:YAG ceramics,” J. Am. Ceram. Soc. 92(7), 1456–1463 (2009).
[Crossref]

Liu, Q.

J. R. Luo, A. Godfrey, W. Liu, and Q. Liu, “Twinning behavior of a strongly basal textured AZ31Mg alloy during warm rolling,” Acta Mater. 60(5), 1986–1998 (2012).
[Crossref]

Liu, W.

J. R. Luo, A. Godfrey, W. Liu, and Q. Liu, “Twinning behavior of a strongly basal textured AZ31Mg alloy during warm rolling,” Acta Mater. 60(5), 1986–1998 (2012).
[Crossref]

Lu, K.

L. Lu, X. Chen, X. Huang, and K. Lu, “Revealing the maximum strength in nanotwinned copper,” Science 323(5914), 607–610 (2009).
[Crossref] [PubMed]

Lu, L.

L. Lu, X. Chen, X. Huang, and K. Lu, “Revealing the maximum strength in nanotwinned copper,” Science 323(5914), 607–610 (2009).
[Crossref] [PubMed]

Luo, J. R.

J. R. Luo, A. Godfrey, W. Liu, and Q. Liu, “Twinning behavior of a strongly basal textured AZ31Mg alloy during warm rolling,” Acta Mater. 60(5), 1986–1998 (2012).
[Crossref]

Maguire, E. A.

T. M. Hartnett, S. D. Bernstein, E. A. Maguire, and R. W. Tustison, “Optical properties of ALON aluminum oxynitride,” Infrared Phys. Technol. 39(4), 203–211 (1998).
[Crossref]

McCauley, J. W.

J. W. McCauley, P. Patel, M. W. Chen, G. Gilde, E. Strassburger, B. Paliwal, K. T. Ramesh, and D. P. Dandekar, “AlON: A brief history of its emergence and evolution,” J. Eur. Ceram. Soc. 29(2), 223–236 (2009).
[Crossref]

Messing, G. L.

S. H. Lee, E. R. Kupp, A. J. Stevenson, J. M. Anderson, G. L. Messing, X. Li, E. C. Dickey, J. Q. Dumm, V. K. Simonaitis-Castillo, and G. J. Quarles, “Hot isostatic pressing of transparent Nd:YAG ceramics,” J. Am. Ceram. Soc. 92(7), 1456–1463 (2009).
[Crossref]

Miller, L.

L. Miller and W. D. Kaplan, “Solubility limits of La and Y in aluminum oxynitride at 1870°C,” J. Am. Ceram. Soc. 91(5), 1693–1696 (2008).
[Crossref]

Ordan’yan, S. S.

S. N. Perevislov, V. D. Chupov, S. S. Ordan’yan, and M. V. Tomkovich, “Obtaining high-density silicon carbide materials by liquid-phase sintering in the system SiC–Al2O3–Y2O3–MgO,” Ogneup. Tekh. Keram 4–5, 26–32 (2011).

Paliwal, B.

J. W. McCauley, P. Patel, M. W. Chen, G. Gilde, E. Strassburger, B. Paliwal, K. T. Ramesh, and D. P. Dandekar, “AlON: A brief history of its emergence and evolution,” J. Eur. Ceram. Soc. 29(2), 223–236 (2009).
[Crossref]

Pande, C. S.

C. S. Pande, M. A. Imam, and B. B. Rath, “Study of annealing twins in FCC metals and alloys,” Met.Trans.A. 21(11), 2891–2896 (1990).
[Crossref]

Patel, P.

J. W. McCauley, P. Patel, M. W. Chen, G. Gilde, E. Strassburger, B. Paliwal, K. T. Ramesh, and D. P. Dandekar, “AlON: A brief history of its emergence and evolution,” J. Eur. Ceram. Soc. 29(2), 223–236 (2009).
[Crossref]

Perevislov, S. N.

S. N. Perevislov, V. D. Chupov, S. S. Ordan’yan, and M. V. Tomkovich, “Obtaining high-density silicon carbide materials by liquid-phase sintering in the system SiC–Al2O3–Y2O3–MgO,” Ogneup. Tekh. Keram 4–5, 26–32 (2011).

Poslusny, D.

D. Clay, D. Poslusny, M. Flinders, S. D. Jacobs, and R. A. Cutler, “Effect of LiAl5O8 additions on the sintering and optical transparency of LiAlON,” J. Eur. Ceram. Soc. 26(8), 1351–1362 (2006).
[Crossref]

Potthoff, A.

A. Krell, T. Hutzler, J. Klimke, and A. Potthoff, “Fine-Grained Transparent spinel windows by the processing of different nanopowders,” J. Am. Ceram. Soc. 93(9), 2656–2666 (2010).
[Crossref]

Quarles, G. J.

S. H. Lee, E. R. Kupp, A. J. Stevenson, J. M. Anderson, G. L. Messing, X. Li, E. C. Dickey, J. Q. Dumm, V. K. Simonaitis-Castillo, and G. J. Quarles, “Hot isostatic pressing of transparent Nd:YAG ceramics,” J. Am. Ceram. Soc. 92(7), 1456–1463 (2009).
[Crossref]

Ramesh, K. T.

J. W. McCauley, P. Patel, M. W. Chen, G. Gilde, E. Strassburger, B. Paliwal, K. T. Ramesh, and D. P. Dandekar, “AlON: A brief history of its emergence and evolution,” J. Eur. Ceram. Soc. 29(2), 223–236 (2009).
[Crossref]

Rath, B. B.

C. S. Pande, M. A. Imam, and B. B. Rath, “Study of annealing twins in FCC metals and alloys,” Met.Trans.A. 21(11), 2891–2896 (1990).
[Crossref]

Simonaitis-Castillo, V. K.

S. H. Lee, E. R. Kupp, A. J. Stevenson, J. M. Anderson, G. L. Messing, X. Li, E. C. Dickey, J. Q. Dumm, V. K. Simonaitis-Castillo, and G. J. Quarles, “Hot isostatic pressing of transparent Nd:YAG ceramics,” J. Am. Ceram. Soc. 92(7), 1456–1463 (2009).
[Crossref]

Stevenson, A. J.

S. H. Lee, E. R. Kupp, A. J. Stevenson, J. M. Anderson, G. L. Messing, X. Li, E. C. Dickey, J. Q. Dumm, V. K. Simonaitis-Castillo, and G. J. Quarles, “Hot isostatic pressing of transparent Nd:YAG ceramics,” J. Am. Ceram. Soc. 92(7), 1456–1463 (2009).
[Crossref]

Strassburger, E.

J. W. McCauley, P. Patel, M. W. Chen, G. Gilde, E. Strassburger, B. Paliwal, K. T. Ramesh, and D. P. Dandekar, “AlON: A brief history of its emergence and evolution,” J. Eur. Ceram. Soc. 29(2), 223–236 (2009).
[Crossref]

Sullivan, R. M.

R. M. Sullivan, “A historical view of AlON,” Proc. SPIE 5786, 23–32 (2005).
[Crossref]

Sun, F.

F. Chen, F. Zhang, J. Wang, H. L. Zhang, R. Tian, J. Zhang, Z. Zhang, F. Sun, and S. W. Wang, “Microstructure and optical properties of transparent aluminum oxynitride ceramics by hot isostatic pressing,” Scr. Mater. 81, 20–23 (2014).
[Crossref]

Sunne, W.

C. T. Warner, T. M. Hartnett, D. Fisher, and W. Sunne, “Characterization of AlON optical ceramic,” Proc. SPIE 5786, 95–111 (2005).
[Crossref]

Tian, R.

J. Wang, F. Zhang, F. Chen, J. Zhang, H. L. Zhang, R. Tian, Z. J. Wang, and S. W. Wang, “Effect of Y2O3 and La2O3 on the sinterability of γ-AlON transparent ceramic,” J. Eur. Ceram. Soc. 35(1), 23–28 (2015).
[Crossref]

F. Chen, F. Zhang, J. Wang, H. L. Zhang, R. Tian, J. Zhang, Z. Zhang, F. Sun, and S. W. Wang, “Microstructure and optical properties of transparent aluminum oxynitride ceramics by hot isostatic pressing,” Scr. Mater. 81, 20–23 (2014).
[Crossref]

Tomkovich, M. V.

S. N. Perevislov, V. D. Chupov, S. S. Ordan’yan, and M. V. Tomkovich, “Obtaining high-density silicon carbide materials by liquid-phase sintering in the system SiC–Al2O3–Y2O3–MgO,” Ogneup. Tekh. Keram 4–5, 26–32 (2011).

Tustison, R. W.

T. M. Hartnett, S. D. Bernstein, E. A. Maguire, and R. W. Tustison, “Optical properties of ALON aluminum oxynitride,” Infrared Phys. Technol. 39(4), 203–211 (1998).
[Crossref]

Vonlanthen, P.

P. Vonlanthen and B. Grobety, “CSL grain boundary distribution in alumina and zirconia ceramics,” Ceram. Int. 34(6), 1459–1472 (2008).
[Crossref]

Wang, J.

J. Wang, F. Zhang, F. Chen, J. Zhang, H. L. Zhang, R. Tian, Z. J. Wang, and S. W. Wang, “Effect of Y2O3 and La2O3 on the sinterability of γ-AlON transparent ceramic,” J. Eur. Ceram. Soc. 35(1), 23–28 (2015).
[Crossref]

F. Chen, F. Zhang, J. Wang, H. L. Zhang, R. Tian, J. Zhang, Z. Zhang, F. Sun, and S. W. Wang, “Microstructure and optical properties of transparent aluminum oxynitride ceramics by hot isostatic pressing,” Scr. Mater. 81, 20–23 (2014).
[Crossref]

Wang, S. W.

J. Wang, F. Zhang, F. Chen, J. Zhang, H. L. Zhang, R. Tian, Z. J. Wang, and S. W. Wang, “Effect of Y2O3 and La2O3 on the sinterability of γ-AlON transparent ceramic,” J. Eur. Ceram. Soc. 35(1), 23–28 (2015).
[Crossref]

F. Chen, F. Zhang, J. Wang, H. L. Zhang, R. Tian, J. Zhang, Z. Zhang, F. Sun, and S. W. Wang, “Microstructure and optical properties of transparent aluminum oxynitride ceramics by hot isostatic pressing,” Scr. Mater. 81, 20–23 (2014).
[Crossref]

Wang, W.

W. Wang, S. L. Korinek, F. Brisset, A. L. Helbert, J. Bourgon, and T. Baudin, “Formation of annealing twins during primary recrystallization of two low stacking fault energy Ni-based alloys,” J. Mater. Sci. 50(5), 2167–2177 (2015).
[Crossref]

Wang, Z. J.

J. Wang, F. Zhang, F. Chen, J. Zhang, H. L. Zhang, R. Tian, Z. J. Wang, and S. W. Wang, “Effect of Y2O3 and La2O3 on the sinterability of γ-AlON transparent ceramic,” J. Eur. Ceram. Soc. 35(1), 23–28 (2015).
[Crossref]

Warner, C. T.

C. T. Warner, T. M. Hartnett, D. Fisher, and W. Sunne, “Characterization of AlON optical ceramic,” Proc. SPIE 5786, 95–111 (2005).
[Crossref]

Wei, M.

M. Wei, D. Zhi, and D. G. Brandon, “Microstructure and texture evolution in gel-cast α-alumina/alumina platelet ceramic composites,” Scr. Mater. 53(12), 1327–1332 (2005).
[Crossref]

Zhang, F.

J. Wang, F. Zhang, F. Chen, J. Zhang, H. L. Zhang, R. Tian, Z. J. Wang, and S. W. Wang, “Effect of Y2O3 and La2O3 on the sinterability of γ-AlON transparent ceramic,” J. Eur. Ceram. Soc. 35(1), 23–28 (2015).
[Crossref]

F. Chen, F. Zhang, J. Wang, H. L. Zhang, R. Tian, J. Zhang, Z. Zhang, F. Sun, and S. W. Wang, “Microstructure and optical properties of transparent aluminum oxynitride ceramics by hot isostatic pressing,” Scr. Mater. 81, 20–23 (2014).
[Crossref]

Zhang, H. L.

J. Wang, F. Zhang, F. Chen, J. Zhang, H. L. Zhang, R. Tian, Z. J. Wang, and S. W. Wang, “Effect of Y2O3 and La2O3 on the sinterability of γ-AlON transparent ceramic,” J. Eur. Ceram. Soc. 35(1), 23–28 (2015).
[Crossref]

F. Chen, F. Zhang, J. Wang, H. L. Zhang, R. Tian, J. Zhang, Z. Zhang, F. Sun, and S. W. Wang, “Microstructure and optical properties of transparent aluminum oxynitride ceramics by hot isostatic pressing,” Scr. Mater. 81, 20–23 (2014).
[Crossref]

Zhang, J.

J. Wang, F. Zhang, F. Chen, J. Zhang, H. L. Zhang, R. Tian, Z. J. Wang, and S. W. Wang, “Effect of Y2O3 and La2O3 on the sinterability of γ-AlON transparent ceramic,” J. Eur. Ceram. Soc. 35(1), 23–28 (2015).
[Crossref]

F. Chen, F. Zhang, J. Wang, H. L. Zhang, R. Tian, J. Zhang, Z. Zhang, F. Sun, and S. W. Wang, “Microstructure and optical properties of transparent aluminum oxynitride ceramics by hot isostatic pressing,” Scr. Mater. 81, 20–23 (2014).
[Crossref]

Zhang, Z.

F. Chen, F. Zhang, J. Wang, H. L. Zhang, R. Tian, J. Zhang, Z. Zhang, F. Sun, and S. W. Wang, “Microstructure and optical properties of transparent aluminum oxynitride ceramics by hot isostatic pressing,” Scr. Mater. 81, 20–23 (2014).
[Crossref]

Zhi, D.

M. Wei, D. Zhi, and D. G. Brandon, “Microstructure and texture evolution in gel-cast α-alumina/alumina platelet ceramic composites,” Scr. Mater. 53(12), 1327–1332 (2005).
[Crossref]

Acta Mater. (1)

J. R. Luo, A. Godfrey, W. Liu, and Q. Liu, “Twinning behavior of a strongly basal textured AZ31Mg alloy during warm rolling,” Acta Mater. 60(5), 1986–1998 (2012).
[Crossref]

Acta Metall. (1)

S. Dash and N. Brown, “An investigation of the origin and growth of annealing twins,” Acta Metall. 11(9), 1067–1075 (1963).
[Crossref]

Ceram. Int. (1)

P. Vonlanthen and B. Grobety, “CSL grain boundary distribution in alumina and zirconia ceramics,” Ceram. Int. 34(6), 1459–1472 (2008).
[Crossref]

Infrared Phys. Technol. (1)

T. M. Hartnett, S. D. Bernstein, E. A. Maguire, and R. W. Tustison, “Optical properties of ALON aluminum oxynitride,” Infrared Phys. Technol. 39(4), 203–211 (1998).
[Crossref]

J. Am. Ceram. Soc. (4)

R. Apetz and M. P. B. V. Bruggen, “Transparent alumina: A light-scattering model,” J. Am. Ceram. Soc. 86(3), 480–486 (2003).
[Crossref]

L. Miller and W. D. Kaplan, “Solubility limits of La and Y in aluminum oxynitride at 1870°C,” J. Am. Ceram. Soc. 91(5), 1693–1696 (2008).
[Crossref]

A. Krell, T. Hutzler, J. Klimke, and A. Potthoff, “Fine-Grained Transparent spinel windows by the processing of different nanopowders,” J. Am. Ceram. Soc. 93(9), 2656–2666 (2010).
[Crossref]

S. H. Lee, E. R. Kupp, A. J. Stevenson, J. M. Anderson, G. L. Messing, X. Li, E. C. Dickey, J. Q. Dumm, V. K. Simonaitis-Castillo, and G. J. Quarles, “Hot isostatic pressing of transparent Nd:YAG ceramics,” J. Am. Ceram. Soc. 92(7), 1456–1463 (2009).
[Crossref]

J. Eur. Ceram. Soc. (3)

J. Wang, F. Zhang, F. Chen, J. Zhang, H. L. Zhang, R. Tian, Z. J. Wang, and S. W. Wang, “Effect of Y2O3 and La2O3 on the sinterability of γ-AlON transparent ceramic,” J. Eur. Ceram. Soc. 35(1), 23–28 (2015).
[Crossref]

D. Clay, D. Poslusny, M. Flinders, S. D. Jacobs, and R. A. Cutler, “Effect of LiAl5O8 additions on the sintering and optical transparency of LiAlON,” J. Eur. Ceram. Soc. 26(8), 1351–1362 (2006).
[Crossref]

J. W. McCauley, P. Patel, M. W. Chen, G. Gilde, E. Strassburger, B. Paliwal, K. T. Ramesh, and D. P. Dandekar, “AlON: A brief history of its emergence and evolution,” J. Eur. Ceram. Soc. 29(2), 223–236 (2009).
[Crossref]

J. Mater. Sci. (1)

W. Wang, S. L. Korinek, F. Brisset, A. L. Helbert, J. Bourgon, and T. Baudin, “Formation of annealing twins during primary recrystallization of two low stacking fault energy Ni-based alloys,” J. Mater. Sci. 50(5), 2167–2177 (2015).
[Crossref]

Met.Trans.A. (1)

C. S. Pande, M. A. Imam, and B. B. Rath, “Study of annealing twins in FCC metals and alloys,” Met.Trans.A. 21(11), 2891–2896 (1990).
[Crossref]

Ogneup. Tekh. Keram (1)

S. N. Perevislov, V. D. Chupov, S. S. Ordan’yan, and M. V. Tomkovich, “Obtaining high-density silicon carbide materials by liquid-phase sintering in the system SiC–Al2O3–Y2O3–MgO,” Ogneup. Tekh. Keram 4–5, 26–32 (2011).

Proc. SPIE (2)

C. T. Warner, T. M. Hartnett, D. Fisher, and W. Sunne, “Characterization of AlON optical ceramic,” Proc. SPIE 5786, 95–111 (2005).
[Crossref]

R. M. Sullivan, “A historical view of AlON,” Proc. SPIE 5786, 23–32 (2005).
[Crossref]

Science (1)

L. Lu, X. Chen, X. Huang, and K. Lu, “Revealing the maximum strength in nanotwinned copper,” Science 323(5914), 607–610 (2009).
[Crossref] [PubMed]

Scr. Mater. (3)

J. L. Bair, S. L. Hatch, and D. P. Field, “Formation of annealing twin boundaries in nickel,” Scr. Mater. 81, 52–55 (2014).
[Crossref]

F. Chen, F. Zhang, J. Wang, H. L. Zhang, R. Tian, J. Zhang, Z. Zhang, F. Sun, and S. W. Wang, “Microstructure and optical properties of transparent aluminum oxynitride ceramics by hot isostatic pressing,” Scr. Mater. 81, 20–23 (2014).
[Crossref]

M. Wei, D. Zhi, and D. G. Brandon, “Microstructure and texture evolution in gel-cast α-alumina/alumina platelet ceramic composites,” Scr. Mater. 53(12), 1327–1332 (2005).
[Crossref]

Cited By

OSA participates in Crossref's Cited-By Linking service. Citing articles from OSA journals and other participating publishers are listed here.

Alert me when this article is cited.


Figures (5)

Fig. 1
Fig. 1 SEM micrograph of single Y2O3 -doped AlON ceramics: (a) 0.08 wt%, (b) 0.10 wt%, (c) 0.12 wt%, and (d) 0.14wt%. (Inset: higher magnification SEM images)
Fig. 2
Fig. 2 SEM micrograph of single La2O3 -doped AlON ceramics: (a) 0.01 wt%, (b) 0.02 wt%, (c) 0.03 wt%, and (d) 0.04 wt% .
Fig. 3
Fig. 3 Twin boundary fractions as a function of the Y2O3/ La2O3 concentrations.(Inset: (a)EBSD orientation map, (b)TBs detected by EBSD, (c) concave or convex TBs, and (d) twin band with a certain thickness)
Fig. 4
Fig. 4 In-line transmittance of AlON ceramics (4.2mm thick) doped with (a) single-La2O3, and (b) single-Y2O3 additives, respectively.
Fig. 5
Fig. 5 (a) SEM and (b) transmittance of 0.08 wt% Y2O3-0.01 wt% La2O3 codoped AlON ceramic.

Tables (1)

Tables Icon

Table 1 Relative densities and grain sizes of HIPed AlON ceramics doped with different additives.

Metrics