Abstract

This paper proposes a reconfigurable planar metamaterial that can be switched between capacitive and inductive responses using local changes in the electrical conductivity of its constituent material. The proposed device is based on Babinet’s principle and exploits the singular electromagnetic responses of metallic checkerboard structures, which are dependent on the local electrical conductivity. Utilizing the heating-induced metal-insulator transition of vanadium dioxide (VO2), the proposed meta-material is designed to compensate for the effect of the substrate and is experimentally characterized in the terahertz regime. This reconfigurable metamaterial can be utilized as a switchable filter and as a switchable phase shifter for terahertz waves.

© 2016 Optical Society of America

1. Introduction

Metamaterials are artificial electromagnetic media that are comprised of unit structures smaller than the wavelength of interest. Their responses can be tailored by tuning the constituent materials, sizes, shapes, and arrangement of the unit cells. Two-dimensional metamaterials are called metasurfaces. Recently, considerable efforts have been made towards the realization of tunable or reconfigurable metamaterials [1], the properties of which are controllable using external stimuli, such as electric fields [2], light [3], and temperature (T) changes [4].

Metamaterial and tunable metamaterial technology is especially important with regard to the terahertz region of the electromagnetic spectrum, because this frequency region lacks efficient manipulation techniques based on conventional electronics or photonics [5]. To eliminate this shortcoming, various active and passive devices based on the metamaterial concept have been studied and developed, including amplitude modulators [6], phase modulators [7], group delay modulators [8], and thin absorbers [9].

In this paper, we propose a reconfigurable metasurface that can alternate between two contrasting behaviors in response to local changes in the electrical conductivity of its constituent material. The developed metasurface is based on metallic-checkerboard structural singularities [10–15 ], the electromagnetic responses of which are strongly dependent on the interconnection state of the metallic squares of the checkerboard. For example, these structures exhibit a high-pass frequency characteristic with a transmission peak for propagating incident waves when the metallic squares are electrically interconnected (“inductive” behavior). However, a low-pass frequency characteristic with a dip is obtained if the metallic parts are not interconnected (“capacitive” behavior) [12]. Therefore, we can dynamically alter the behavior of these devices by switching the local electrical conductivity at the interconnection points of the metallic squares. This reconfigurable characteristic of the metasurface can be exploited for switchable filter and switchable phase shifter applications for terahertz waves. We note that, although similar functionality has been realized by exploiting the characteristics of anisotropic self-complementary metasurfaces [16], mechanical rotation of the metasurface itself is required to accomplish the reconfiguration in such cases.

Here, we use vanadium dioxide (VO2) to achieve the electrical conductivity switching. VO2 exhibits a metal-insulator transition at T ≈ 340K [17], which is relatively close to room temperature, and the electrical conductivity typically changes by several orders of magnitude. In addition, the VO2 phase transition can be triggered by other external stimuli, including a high electric field [18] and photoexcitation [19]. Hence, VO2 is a suitable material for realization of the proposed reconfigurable metasurface.

2. Operating principles

Babinet’s principle for vector waves relates the scattering problem for a metallic metasurface to that of its complementary structure, which is obtained by interchanging the metallic and vacant areas of the original metasurface [20]. This principle can be extended to cases where the metallic metasurfaces contain resistive elements [14, 21]. In this extension, regions with high electrical conductivity have corresponding low-electrical-conductivity regions in the complementary structure, and vice versa (this operation is called Babinet inversion). Hereafter, we assume that the incident wave is a linearly polarized plane wave with angular frequency ω. Note that the incident polarization in the complementary scattering problem is orthogonal to that in the original problem. For the zeroth-order transmission mode, a simple relationship exists between the original and complementary problems [14, 15]

t˜(ω)+t˜c(ω)=1,
where t˜(ω) and t˜c(ω) are the complex amplitude transmission coefficients of the zeroth-order transmission modes in the original problem and its complement, respectively. Moreover, if scattering into higher-order diffraction modes and ohmic losses are negligible in each problem, t˜(ω) and t˜c(ω) are in quadrature phase to each other [22].

Let us consider a plane-wave scattering problem involving a metallic checkerboard-like metasurface, as shown in Fig. 1(a). We assume that the local electrical conductivity at the interconnection points of the metallic patches is sufficiently low and, thus, the metallic squares are electrically disconnected. Such a structure exhibits capacitive behavior with a transmission dip at frequency ω0[t˜(ω0)0]. This is referred to as the off state. The corresponding Babinet-inverted structure is shown in Fig. 1(b). In this case, as a result of Babinet’s principle, the local electrical conductivity at the interconnection points of the metallic patches must be high, and the polarization of the incident plane wave is rotated by π/2. The Babinet-inverted structure exhibits inductive behavior with a transmission peak at ω 0, according to Babinet’s principle [t˜c(ω0)1]. However, if the electrical conductivity at the interconnection points is increased, the off state in Fig. 1(a) transits to the on state shown in Fig. 1(c). In other words, the metallic squares become electrically connected. As a result of the four-fold rotational symmetry of the metasurface, the scattering problem of the on state shown in Fig. 1(c) is equivalent to that of the Babinet-inverted structure shown in Fig. 1(b), provided normal incidence is assumed. Therefore, the transmission characteristic in the on state is identical to that in the Babinet-inverted structure derived from the off state. This means that we can dynamically alter the behavior of the metasurface to the complementary behavior of its Babinet-inverted structure, simply by switching the local electrical conductivity at the interconnection points of the checkerboard. Hence, we refer to this reconfigurable metasurface as a Babinet-invertible metasurface.

 

Fig. 1 Principles of Babinet-invertible metasurface. (a) Off state. (b) Babinet-inverted structure. Note that the polarization of the incident wave is orthogonal to that in the off state. (c) On state. The vectors E, H, and k indicate the electric field, the magnetic field, and the wavevector of the incident plane waves, respectively.

Download Full Size | PPT Slide | PDF

It should be noted that Babinet’s principle does not hold strictly if the planar structure is placed on a substrate, which breaks the inversion symmetry with respect to the metasurface plane. However, it is known that a qualitatively similar relationship exists between the characteristics of the metallic complementary structures, even in the presence of substrates [23, 24]. Therefore, the above principle is applicable to a Babinet-invertible metasurface with moderate-refractive-index substrates.

3. Sample design and fabrication

Figure 2(a) shows the design employed to realize the Babinet-invertible metasurface using VO2. The small VO2 patches are located at the interconnection points of the checkerboard. Below the critical temperature T c ~ 340K of VO2, the patches are insulating and, therefore, the metasurface is in the off state. By increasing T above T c, the VO2 insulator-to-metal transition is induced and, thus, the metasurface transits to the on state. The Al structures overlap the VO2 patches, ensuring electrical connection. The width g of the gaps between the metallic structures in Fig. 2(a) is narrower than those in the ideal case without a substrate, as shown in Fig. 1. This modification is introduced in order to compensate for the difference between the dip and peak frequencies in the transmission characteristics due to the dielectric substrate. This compensation is achieved by increasing the gap capacitance; otherwise, the transmission dip frequency would be slightly higher than the transmission peak frequency. In addition, the small g decreases the resistance of the interconnection points, which leads to a high transmission peak in the on state. The optimal value of g is heuristically found via numerical simulations using a commercial finite-element method solution package (COMSOL Multiphysics). Figure 2(b) shows the calculated g dependence of the on-off ratio of the power transmission at the peak and dip frequencies and their frequency difference. To obtain high on-off ratio and small frequency difference, we choose g = 5µm.

 

Fig. 2 (a) Babinet-invertible metasurface design. The parameters are as follows: a = 75µm, g = 5µm, u = 15µm, and d = 32µm. The broken lines indicate the area where the Al structures overlap the VO2. (b) Calculated g dependence of the on-off ratio of the power transmission at the peak and dip frequencies and their frequency difference. (c) Photograph of fabricated metasurface. The exposed regions of the VO2 patches are digitally colored in turquoise for clarity.

Download Full Size | PPT Slide | PDF

The designed metasurface is fabricated as follows. A thin film of stoichiometric VO2 with 1-µm thickness is prepared on a sapphire (0001) substrate (thickness: 0.9 mm) via reactive magnetron sputtering of a vanadium target [25]. The sputtering conditions are as follows: substrate T: 400°C; radio frequency (rf) power: 200W; Ar flow rate: 0.11Pa·m3/s; O2 flow rate: 1.4 × 10 3 Pa·m3/s; and total Ar and O2 pressure: 0.5Pa. These conditions yield a deposition rate of ~ 8nm/min. Photoresist is spin-coated on the VO2 film and then patterned as an etching mask using photolithography. The exposed part of the VO2 film is removed by wet etching with a mixture comprised of phosphoric acid, nitric acid, acetic acid, and water, at a 16:1:2:1 ratio. Then, an Al checkerboard (thickness: 400nm) is fabricated on the sample via standard photolithography, electron beam evaporation at room temperature, and lift-off techniques. A photograph of the sample is shown in Fig. 2(c). As a result of the surface roughness of the VO2 patches, the regions in which the Al structures overlap the VO2 appear dark and roughly textured compared with the other Al regions.

4. Characterization

We use the terahertz time-domain spectroscopy technique [26] for characterization of the fabricated metasurface. The metasurface is set on a sample holder, the temperature of which is stabilized through temperature feedback control of the electric current in a nichrome wire attached to the holder. The value of the holder T is monitored using a thermocouple, and the sample holder is covered by styrene boards for thermal insulation. We generate and detect terahertz pulses through the photoexcitation of photoconductive dipole antennas on low-temperature-grown GaAs substrates. The emitted terahertz beam is linearly polarized and focused onto the sample under normal incidence by a Si hyper-hemispherical lens and a subsequent Tsurupica lens. The beam diameter at the focal plane is ~ 5mm and the incident polarization is in the y-direction indicated in Fig. 2(a). While changing the T value of the sample holder, we measure the temporal waveforms of the terahertz electric fields transmitted through the sample and, also, through a plain sapphire plate (as a reference measurement). These measurements are performed under dry air purged conditions. The transmission coefficient spectra t˜(ω) are obtained by dividing the Fourier transforms of the electric fields transmitted through the sample by those of the reference measurement, where the echo pulses caused by the reflections at the sample-air boundaries are removed by setting a time window, and the time dependence exp(jωt) is assumed.

Figures 3(a) and 3(b) show the measured transmission amplitude |t˜(ω)| and phase shift arg t˜(ω) spectra, respectively, at T = 300 and 370K. Hence, it is confirmed that the response of the metasurface switches from capacitive to inductive behavior with increased T. In other words, the off state at low T transits to the on state above the Tc of the VO2. It should be noted that the metasurface in the on state returns to the off state if it cools down due to the reversibility of the VO2 phase transition. At 0.77THz, the modulation depth amounts to 14dB, which is limited by the conductivities of the insulating and metallic VO2 phases at low and high T, respectively. In the lower-frequency region of the phase spectra much below the lowest diffraction frequency 0.83THz, where scattering into higher-order diffraction modes is negligible, there is an almost constant phase difference of ~ π/2 between T = 300 and 370K, as a result of Babinet’s principle. In particular, at 0.47THz or the crossing frequency of the two amplitude spectra, the relative transmission phase shift of the metasurface can be switched to the quadrature phase without changing the transmission amplitude. We note that these characteristics of the metasurface are independent of the incident polarization states, provided normal incidence is assumed; this behavior is a result of the four-fold rotational symmetry.

 

Fig. 3 Measured transmission coefficient spectra at T = 300 and 370K: (a) amplitude transmission spectra and (b) phase shift spectra.

Download Full Size | PPT Slide | PDF

5. Conclusion

In conclusion, we have proposed a reconfigurable metasurface that is transformable into its Babinet-inverted structure by exploiting the singularities of a metallic checkerboard structure and the metal-insulator transition of VO2. The operation of the metasurface has been confirmed experimentally. The Babinet-invertible metasurface equipped with a thermostat can be utilized as a switchable filter and as a switchable π/2 phase shifter for terahertz waves. The design principles discussed in this study can be realized using not only VO2, but also other conductivity-tunable materials or structures such as photodoped semiconductors, superconductors, non-volatile conductivity changes used in resistive memory devices, and microelectromechanical systems. We also note that the present metasurface is expected to exhibit nonlinear behavior for intense terahertz pulses inducing phase transition of the VO2, which will be used as an optical fuse [27].

Acknowledgments

The authors thank Dr. Keisuke Takano and Prof. Masanori Hangyo for useful discussions, and Dr. Joe Sakai for his helpful comments on the etching process. This work was partly supported by JSPS KAKENHI grants (15J07603, 25790065, 25287101) and by research grants from the Murata Science Foundation (Y.N.). The sample fabrication was performed with the help of Kyoto University Nano Technology Hub, as part of the “Nanotechnology Platform Project” sponsored by MEXT in Japan. One of the authors (Y.U.) was supported by a JSPS Research Fellowship for Young Scientists.

References and links

1. N. I. Zheludev and Y. S. Kivshar, “From metamaterials to metadevices,” Nat. Mater. 11, 917–924 (2012). [CrossRef]   [PubMed]  

2. T. Kan, A. Isozaki, N. Kanda, N. Nemoto, K. Konishi, M. Kuwata-Gonokami, K. Matsumoto, and I. Shimoyama, “Spiral metamaterial for active tuning of optical activity,” Appl. Phys. Lett. 102, 221906 (2013). [CrossRef]  

3. I. V. Shadrivov, P. V. Kapitanova, S. I. Maslovski, and Y. S. Kivshar, “Metamaterials controlled with light,” Phys. Rev. Lett. 109, 083902 (2012). [CrossRef]   [PubMed]  

4. J. Y. Ou, E. Plum, L. Jiang, and N. I. Zheludev, “Reconfigurable photonic metamaterials,” Nano Lett. 11, 2142–2144 (2011). [CrossRef]   [PubMed]  

5. H. Tao, W. J. Padilla, X. Zhang, and R. D. Averitt, “Recent progress in electromagnetic metamaterial devices for terahertz applications,” IEEE J. Sel. Top. Quantum Electron. 17, 92–101 (2011). [CrossRef]  

6. H.-T. Chen, W. J. Padilla, J. M. O. Zide, A. C. Gossard, A. J. Taylor, and R. D. Averitt, “Active terahertz meta-material devices,” Nature 444, 597–600 (2006). [CrossRef]   [PubMed]  

7. H.-T. Chen, W. J. Padilla, M. J. Cich, A. K. Azad, R. D. Averitt, and A. J. Taylor, “A metamaterial solid-state terahertz phase modulator,” Nat. Photonics 3, 148–151 (2009). [CrossRef]  

8. F. Miyamaru, H. Morita, Y. Nishiyama, T. Nishida, T. Nakanishi, M. Kitano, and M. W. Takeda, “Ultrafast optical control of group delay of narrow-band terahertz waves,” Sci. Rep. 4, 4346 (2014). [CrossRef]   [PubMed]  

9. H. Tao, N. I. Landy, C. M. Bingham, X. Zhang, R. D. Averitt, and W. J. Padilla, “A metamaterial absorber for the terahertz regime: design, fabrication and characterization,” Opt. Express 16, 7181–7188 (2008). [CrossRef]   [PubMed]  

10. J. D. Edmunds, A. P. Hibbins, J. R. Sambles, and I. J. Youngs, “Resonantly inverted microwave transmissivity threshold of metal grids,” New J. Phys. 12, 063007 (2010). [CrossRef]  

11. K. Kempa, “Percolation effects in the checkerboard babinet series of metamaterial structures,” Phys. Status Solidi Rapid Res. Lett. 4, 218–220 (2010). [CrossRef]  

12. K. Takano, F. Miyamaru, K. Akiyama, H. Miyazaki, M. W. Takeda, Y. Abe, Y. Tokuda, H. Ito, and M. Hangyo, “Crossover from capacitive to inductive electromagnetic responses in near self-complementary metallic checker-board patterns,” Opt. Express 22, 24787–24795 (2014). [CrossRef]   [PubMed]  

13. D. Gonzalez-Ovejero, E. Martini, B. Loiseaux, C. Tripon-Canseliet, M. Mencagli, J. Chazelas, and S. Maci, “Basic properties of checkerboard metasurfaces,” IEEE Antennas Wireless Propag. Lett. 14, 406–409 (2015). [CrossRef]  

14. Y. Nakata, Y. Urade, T. Nakanishi, and M. Kitano, “Plane-wave scattering by self-complementary metasurfaces in terms of electromagnetic duality and Babinet’s principle,” Phys. Rev. B 88, 205138 (2013). [CrossRef]  

15. Y. Urade, Y. Nakata, T. Nakanishi, and M. Kitano, “Frequency-independent response of self-complementary checkerboard screens,” Phys. Rev. Lett. 114, 237401 (2015). [CrossRef]   [PubMed]  

16. J. D. Ortiz, J. D. Baena, V. Losada, F. Medina, R. Marques, and J. A. Quijano, “Self-complementary metasurface for designing narrow band pass/stop filters,” IEEE Microw. Wirel. Components Lett. 23, 291–293 (2013). [CrossRef]  

17. F. J. Morin, “Oxides which show a metal-to-insulator transition at the Neel temperature,” Phys. Rev. Lett. 3, 34 (1959). [CrossRef]  

18. K. Okimura, Y. Sasakawa, and Y. Nihei, “X-ray diffraction study of electric field-induced metal-insulator transition of vanadium dioxide film on sapphire substrate,” Jpn. J. Appl. Phys. 45, 9200–9202 (2006). [CrossRef]  

19. A. Cavalleri, Cs. Tóth, C. W. Siders, J. A. Squier, F. Ráksi, P. Forget, and J. C. Kieffer, “Femtosecond structural dynamics in VO2 during an ultrafast solid-solid phase transition,” Phys. Rev. Lett. 87, 237401 (2001). [CrossRef]  

20. J. A. Kong, Electromagnetic Wave Theory, 2 (Wiley, 1990).

21. C. E. Baum and B. K. Singaraju, “Generalization of Babinet’s principle in terms of the combined field to include impedance loaded aperture antennas and scatterers,” Interaction Note No. 217, Air Force Weapons Lab., Kirtland Air Force Base, NM87117 (1974).

22. J. D. Baena, J. P. del Risco, A. P. Slobozhanyuk, S. B. Glybovski, and P. A. Belov, “Self-complementary meta-surfaces for linear-to-circular polarization conversion,” Phys. Rev. B 92, 245413 (2015). [CrossRef]  

23. H.-T. Chen, J. F. O’Hara, A. J. Taylor, R. D. Averitt, C. Highstrete, M. Lee, and W. J. Padilla, “Complementary planar terahertz metamaterials,” Opt. Express 15, 1084–1095 (2007). [CrossRef]   [PubMed]  

24. T. Zentgraf, T. Meyrath, A. Seidel, S. Kaiser, H. Giessen, C. Rockstuhl, and F. Lederer, “Babinet’s principle for optical frequency metamaterials and nanoantennas,” Phys. Rev. B 76, 033407 (2007). [CrossRef]  

25. K. Okimura and N. Kubo, “Preparation of VO2 films with metal-insulator transition on sapphire and silicon substrates by inductively coupled plasma-assisted sputtering,” Jpn. J. Appl. Phys. 44, 1150–1153 (2005). [CrossRef]  

26. D. Grischkowsky, S. Keiding, M. van Exter, and C. Fattinger, “Far-infrared time-domain spectroscopy with terahertz beams of dielectrics and semiconductors,” J. Opt. Soc. Am. B 7, 2006 (1990). [CrossRef]  

27. A. C. Strikwerda, M. Zalkovskij, K. Iwaszczuk, D. L. Lorenzen, and P. U. Jepsen, “Permanently reconfigured metamaterials due to terahertz induced mass transfer of gold,” Opt. Express 23, 11586–11599 (2015). [CrossRef]   [PubMed]  

References

  • View by:
  • |
  • |
  • |

  1. N. I. Zheludev and Y. S. Kivshar, “From metamaterials to metadevices,” Nat. Mater. 11, 917–924 (2012).
    [Crossref] [PubMed]
  2. T. Kan, A. Isozaki, N. Kanda, N. Nemoto, K. Konishi, M. Kuwata-Gonokami, K. Matsumoto, and I. Shimoyama, “Spiral metamaterial for active tuning of optical activity,” Appl. Phys. Lett. 102, 221906 (2013).
    [Crossref]
  3. I. V. Shadrivov, P. V. Kapitanova, S. I. Maslovski, and Y. S. Kivshar, “Metamaterials controlled with light,” Phys. Rev. Lett. 109, 083902 (2012).
    [Crossref] [PubMed]
  4. J. Y. Ou, E. Plum, L. Jiang, and N. I. Zheludev, “Reconfigurable photonic metamaterials,” Nano Lett. 11, 2142–2144 (2011).
    [Crossref] [PubMed]
  5. H. Tao, W. J. Padilla, X. Zhang, and R. D. Averitt, “Recent progress in electromagnetic metamaterial devices for terahertz applications,” IEEE J. Sel. Top. Quantum Electron. 17, 92–101 (2011).
    [Crossref]
  6. H.-T. Chen, W. J. Padilla, J. M. O. Zide, A. C. Gossard, A. J. Taylor, and R. D. Averitt, “Active terahertz meta-material devices,” Nature 444, 597–600 (2006).
    [Crossref] [PubMed]
  7. H.-T. Chen, W. J. Padilla, M. J. Cich, A. K. Azad, R. D. Averitt, and A. J. Taylor, “A metamaterial solid-state terahertz phase modulator,” Nat. Photonics 3, 148–151 (2009).
    [Crossref]
  8. F. Miyamaru, H. Morita, Y. Nishiyama, T. Nishida, T. Nakanishi, M. Kitano, and M. W. Takeda, “Ultrafast optical control of group delay of narrow-band terahertz waves,” Sci. Rep. 4, 4346 (2014).
    [Crossref] [PubMed]
  9. H. Tao, N. I. Landy, C. M. Bingham, X. Zhang, R. D. Averitt, and W. J. Padilla, “A metamaterial absorber for the terahertz regime: design, fabrication and characterization,” Opt. Express 16, 7181–7188 (2008).
    [Crossref] [PubMed]
  10. J. D. Edmunds, A. P. Hibbins, J. R. Sambles, and I. J. Youngs, “Resonantly inverted microwave transmissivity threshold of metal grids,” New J. Phys. 12, 063007 (2010).
    [Crossref]
  11. K. Kempa, “Percolation effects in the checkerboard babinet series of metamaterial structures,” Phys. Status Solidi Rapid Res. Lett. 4, 218–220 (2010).
    [Crossref]
  12. K. Takano, F. Miyamaru, K. Akiyama, H. Miyazaki, M. W. Takeda, Y. Abe, Y. Tokuda, H. Ito, and M. Hangyo, “Crossover from capacitive to inductive electromagnetic responses in near self-complementary metallic checker-board patterns,” Opt. Express 22, 24787–24795 (2014).
    [Crossref] [PubMed]
  13. D. Gonzalez-Ovejero, E. Martini, B. Loiseaux, C. Tripon-Canseliet, M. Mencagli, J. Chazelas, and S. Maci, “Basic properties of checkerboard metasurfaces,” IEEE Antennas Wireless Propag. Lett. 14, 406–409 (2015).
    [Crossref]
  14. Y. Nakata, Y. Urade, T. Nakanishi, and M. Kitano, “Plane-wave scattering by self-complementary metasurfaces in terms of electromagnetic duality and Babinet’s principle,” Phys. Rev. B 88, 205138 (2013).
    [Crossref]
  15. Y. Urade, Y. Nakata, T. Nakanishi, and M. Kitano, “Frequency-independent response of self-complementary checkerboard screens,” Phys. Rev. Lett. 114, 237401 (2015).
    [Crossref] [PubMed]
  16. J. D. Ortiz, J. D. Baena, V. Losada, F. Medina, R. Marques, and J. A. Quijano, “Self-complementary metasurface for designing narrow band pass/stop filters,” IEEE Microw. Wirel. Components Lett. 23, 291–293 (2013).
    [Crossref]
  17. F. J. Morin, “Oxides which show a metal-to-insulator transition at the Neel temperature,” Phys. Rev. Lett. 3, 34 (1959).
    [Crossref]
  18. K. Okimura, Y. Sasakawa, and Y. Nihei, “X-ray diffraction study of electric field-induced metal-insulator transition of vanadium dioxide film on sapphire substrate,” Jpn. J. Appl. Phys. 45, 9200–9202 (2006).
    [Crossref]
  19. A. Cavalleri, Cs. Tóth, C. W. Siders, J. A. Squier, F. Ráksi, P. Forget, and J. C. Kieffer, “Femtosecond structural dynamics in VO2 during an ultrafast solid-solid phase transition,” Phys. Rev. Lett. 87, 237401 (2001).
    [Crossref]
  20. J. A. Kong, Electromagnetic Wave Theory, 2 (Wiley, 1990).
  21. C. E. Baum and B. K. Singaraju, “Generalization of Babinet’s principle in terms of the combined field to include impedance loaded aperture antennas and scatterers,” Interaction Note No. 217, Air Force Weapons Lab., Kirtland Air Force Base, NM87117 (1974).
  22. J. D. Baena, J. P. del Risco, A. P. Slobozhanyuk, S. B. Glybovski, and P. A. Belov, “Self-complementary meta-surfaces for linear-to-circular polarization conversion,” Phys. Rev. B 92, 245413 (2015).
    [Crossref]
  23. H.-T. Chen, J. F. O’Hara, A. J. Taylor, R. D. Averitt, C. Highstrete, M. Lee, and W. J. Padilla, “Complementary planar terahertz metamaterials,” Opt. Express 15, 1084–1095 (2007).
    [Crossref] [PubMed]
  24. T. Zentgraf, T. Meyrath, A. Seidel, S. Kaiser, H. Giessen, C. Rockstuhl, and F. Lederer, “Babinet’s principle for optical frequency metamaterials and nanoantennas,” Phys. Rev. B 76, 033407 (2007).
    [Crossref]
  25. K. Okimura and N. Kubo, “Preparation of VO2 films with metal-insulator transition on sapphire and silicon substrates by inductively coupled plasma-assisted sputtering,” Jpn. J. Appl. Phys. 44, 1150–1153 (2005).
    [Crossref]
  26. D. Grischkowsky, S. Keiding, M. van Exter, and C. Fattinger, “Far-infrared time-domain spectroscopy with terahertz beams of dielectrics and semiconductors,” J. Opt. Soc. Am. B 7, 2006 (1990).
    [Crossref]
  27. A. C. Strikwerda, M. Zalkovskij, K. Iwaszczuk, D. L. Lorenzen, and P. U. Jepsen, “Permanently reconfigured metamaterials due to terahertz induced mass transfer of gold,” Opt. Express 23, 11586–11599 (2015).
    [Crossref] [PubMed]

2015 (4)

D. Gonzalez-Ovejero, E. Martini, B. Loiseaux, C. Tripon-Canseliet, M. Mencagli, J. Chazelas, and S. Maci, “Basic properties of checkerboard metasurfaces,” IEEE Antennas Wireless Propag. Lett. 14, 406–409 (2015).
[Crossref]

Y. Urade, Y. Nakata, T. Nakanishi, and M. Kitano, “Frequency-independent response of self-complementary checkerboard screens,” Phys. Rev. Lett. 114, 237401 (2015).
[Crossref] [PubMed]

J. D. Baena, J. P. del Risco, A. P. Slobozhanyuk, S. B. Glybovski, and P. A. Belov, “Self-complementary meta-surfaces for linear-to-circular polarization conversion,” Phys. Rev. B 92, 245413 (2015).
[Crossref]

A. C. Strikwerda, M. Zalkovskij, K. Iwaszczuk, D. L. Lorenzen, and P. U. Jepsen, “Permanently reconfigured metamaterials due to terahertz induced mass transfer of gold,” Opt. Express 23, 11586–11599 (2015).
[Crossref] [PubMed]

2014 (2)

2013 (3)

T. Kan, A. Isozaki, N. Kanda, N. Nemoto, K. Konishi, M. Kuwata-Gonokami, K. Matsumoto, and I. Shimoyama, “Spiral metamaterial for active tuning of optical activity,” Appl. Phys. Lett. 102, 221906 (2013).
[Crossref]

J. D. Ortiz, J. D. Baena, V. Losada, F. Medina, R. Marques, and J. A. Quijano, “Self-complementary metasurface for designing narrow band pass/stop filters,” IEEE Microw. Wirel. Components Lett. 23, 291–293 (2013).
[Crossref]

Y. Nakata, Y. Urade, T. Nakanishi, and M. Kitano, “Plane-wave scattering by self-complementary metasurfaces in terms of electromagnetic duality and Babinet’s principle,” Phys. Rev. B 88, 205138 (2013).
[Crossref]

2012 (2)

I. V. Shadrivov, P. V. Kapitanova, S. I. Maslovski, and Y. S. Kivshar, “Metamaterials controlled with light,” Phys. Rev. Lett. 109, 083902 (2012).
[Crossref] [PubMed]

N. I. Zheludev and Y. S. Kivshar, “From metamaterials to metadevices,” Nat. Mater. 11, 917–924 (2012).
[Crossref] [PubMed]

2011 (2)

J. Y. Ou, E. Plum, L. Jiang, and N. I. Zheludev, “Reconfigurable photonic metamaterials,” Nano Lett. 11, 2142–2144 (2011).
[Crossref] [PubMed]

H. Tao, W. J. Padilla, X. Zhang, and R. D. Averitt, “Recent progress in electromagnetic metamaterial devices for terahertz applications,” IEEE J. Sel. Top. Quantum Electron. 17, 92–101 (2011).
[Crossref]

2010 (2)

J. D. Edmunds, A. P. Hibbins, J. R. Sambles, and I. J. Youngs, “Resonantly inverted microwave transmissivity threshold of metal grids,” New J. Phys. 12, 063007 (2010).
[Crossref]

K. Kempa, “Percolation effects in the checkerboard babinet series of metamaterial structures,” Phys. Status Solidi Rapid Res. Lett. 4, 218–220 (2010).
[Crossref]

2009 (1)

H.-T. Chen, W. J. Padilla, M. J. Cich, A. K. Azad, R. D. Averitt, and A. J. Taylor, “A metamaterial solid-state terahertz phase modulator,” Nat. Photonics 3, 148–151 (2009).
[Crossref]

2008 (1)

2007 (2)

H.-T. Chen, J. F. O’Hara, A. J. Taylor, R. D. Averitt, C. Highstrete, M. Lee, and W. J. Padilla, “Complementary planar terahertz metamaterials,” Opt. Express 15, 1084–1095 (2007).
[Crossref] [PubMed]

T. Zentgraf, T. Meyrath, A. Seidel, S. Kaiser, H. Giessen, C. Rockstuhl, and F. Lederer, “Babinet’s principle for optical frequency metamaterials and nanoantennas,” Phys. Rev. B 76, 033407 (2007).
[Crossref]

2006 (2)

H.-T. Chen, W. J. Padilla, J. M. O. Zide, A. C. Gossard, A. J. Taylor, and R. D. Averitt, “Active terahertz meta-material devices,” Nature 444, 597–600 (2006).
[Crossref] [PubMed]

K. Okimura, Y. Sasakawa, and Y. Nihei, “X-ray diffraction study of electric field-induced metal-insulator transition of vanadium dioxide film on sapphire substrate,” Jpn. J. Appl. Phys. 45, 9200–9202 (2006).
[Crossref]

2005 (1)

K. Okimura and N. Kubo, “Preparation of VO2 films with metal-insulator transition on sapphire and silicon substrates by inductively coupled plasma-assisted sputtering,” Jpn. J. Appl. Phys. 44, 1150–1153 (2005).
[Crossref]

2001 (1)

A. Cavalleri, Cs. Tóth, C. W. Siders, J. A. Squier, F. Ráksi, P. Forget, and J. C. Kieffer, “Femtosecond structural dynamics in VO2 during an ultrafast solid-solid phase transition,” Phys. Rev. Lett. 87, 237401 (2001).
[Crossref]

1990 (1)

1959 (1)

F. J. Morin, “Oxides which show a metal-to-insulator transition at the Neel temperature,” Phys. Rev. Lett. 3, 34 (1959).
[Crossref]

Abe, Y.

Akiyama, K.

Averitt, R. D.

H. Tao, W. J. Padilla, X. Zhang, and R. D. Averitt, “Recent progress in electromagnetic metamaterial devices for terahertz applications,” IEEE J. Sel. Top. Quantum Electron. 17, 92–101 (2011).
[Crossref]

H.-T. Chen, W. J. Padilla, M. J. Cich, A. K. Azad, R. D. Averitt, and A. J. Taylor, “A metamaterial solid-state terahertz phase modulator,” Nat. Photonics 3, 148–151 (2009).
[Crossref]

H. Tao, N. I. Landy, C. M. Bingham, X. Zhang, R. D. Averitt, and W. J. Padilla, “A metamaterial absorber for the terahertz regime: design, fabrication and characterization,” Opt. Express 16, 7181–7188 (2008).
[Crossref] [PubMed]

H.-T. Chen, J. F. O’Hara, A. J. Taylor, R. D. Averitt, C. Highstrete, M. Lee, and W. J. Padilla, “Complementary planar terahertz metamaterials,” Opt. Express 15, 1084–1095 (2007).
[Crossref] [PubMed]

H.-T. Chen, W. J. Padilla, J. M. O. Zide, A. C. Gossard, A. J. Taylor, and R. D. Averitt, “Active terahertz meta-material devices,” Nature 444, 597–600 (2006).
[Crossref] [PubMed]

Azad, A. K.

H.-T. Chen, W. J. Padilla, M. J. Cich, A. K. Azad, R. D. Averitt, and A. J. Taylor, “A metamaterial solid-state terahertz phase modulator,” Nat. Photonics 3, 148–151 (2009).
[Crossref]

Baena, J. D.

J. D. Baena, J. P. del Risco, A. P. Slobozhanyuk, S. B. Glybovski, and P. A. Belov, “Self-complementary meta-surfaces for linear-to-circular polarization conversion,” Phys. Rev. B 92, 245413 (2015).
[Crossref]

J. D. Ortiz, J. D. Baena, V. Losada, F. Medina, R. Marques, and J. A. Quijano, “Self-complementary metasurface for designing narrow band pass/stop filters,” IEEE Microw. Wirel. Components Lett. 23, 291–293 (2013).
[Crossref]

Baum, C. E.

C. E. Baum and B. K. Singaraju, “Generalization of Babinet’s principle in terms of the combined field to include impedance loaded aperture antennas and scatterers,” Interaction Note No. 217, Air Force Weapons Lab., Kirtland Air Force Base, NM87117 (1974).

Belov, P. A.

J. D. Baena, J. P. del Risco, A. P. Slobozhanyuk, S. B. Glybovski, and P. A. Belov, “Self-complementary meta-surfaces for linear-to-circular polarization conversion,” Phys. Rev. B 92, 245413 (2015).
[Crossref]

Bingham, C. M.

Cavalleri, A.

A. Cavalleri, Cs. Tóth, C. W. Siders, J. A. Squier, F. Ráksi, P. Forget, and J. C. Kieffer, “Femtosecond structural dynamics in VO2 during an ultrafast solid-solid phase transition,” Phys. Rev. Lett. 87, 237401 (2001).
[Crossref]

Chazelas, J.

D. Gonzalez-Ovejero, E. Martini, B. Loiseaux, C. Tripon-Canseliet, M. Mencagli, J. Chazelas, and S. Maci, “Basic properties of checkerboard metasurfaces,” IEEE Antennas Wireless Propag. Lett. 14, 406–409 (2015).
[Crossref]

Chen, H.-T.

H.-T. Chen, W. J. Padilla, M. J. Cich, A. K. Azad, R. D. Averitt, and A. J. Taylor, “A metamaterial solid-state terahertz phase modulator,” Nat. Photonics 3, 148–151 (2009).
[Crossref]

H.-T. Chen, J. F. O’Hara, A. J. Taylor, R. D. Averitt, C. Highstrete, M. Lee, and W. J. Padilla, “Complementary planar terahertz metamaterials,” Opt. Express 15, 1084–1095 (2007).
[Crossref] [PubMed]

H.-T. Chen, W. J. Padilla, J. M. O. Zide, A. C. Gossard, A. J. Taylor, and R. D. Averitt, “Active terahertz meta-material devices,” Nature 444, 597–600 (2006).
[Crossref] [PubMed]

Cich, M. J.

H.-T. Chen, W. J. Padilla, M. J. Cich, A. K. Azad, R. D. Averitt, and A. J. Taylor, “A metamaterial solid-state terahertz phase modulator,” Nat. Photonics 3, 148–151 (2009).
[Crossref]

del Risco, J. P.

J. D. Baena, J. P. del Risco, A. P. Slobozhanyuk, S. B. Glybovski, and P. A. Belov, “Self-complementary meta-surfaces for linear-to-circular polarization conversion,” Phys. Rev. B 92, 245413 (2015).
[Crossref]

Edmunds, J. D.

J. D. Edmunds, A. P. Hibbins, J. R. Sambles, and I. J. Youngs, “Resonantly inverted microwave transmissivity threshold of metal grids,” New J. Phys. 12, 063007 (2010).
[Crossref]

Fattinger, C.

Forget, P.

A. Cavalleri, Cs. Tóth, C. W. Siders, J. A. Squier, F. Ráksi, P. Forget, and J. C. Kieffer, “Femtosecond structural dynamics in VO2 during an ultrafast solid-solid phase transition,” Phys. Rev. Lett. 87, 237401 (2001).
[Crossref]

Giessen, H.

T. Zentgraf, T. Meyrath, A. Seidel, S. Kaiser, H. Giessen, C. Rockstuhl, and F. Lederer, “Babinet’s principle for optical frequency metamaterials and nanoantennas,” Phys. Rev. B 76, 033407 (2007).
[Crossref]

Glybovski, S. B.

J. D. Baena, J. P. del Risco, A. P. Slobozhanyuk, S. B. Glybovski, and P. A. Belov, “Self-complementary meta-surfaces for linear-to-circular polarization conversion,” Phys. Rev. B 92, 245413 (2015).
[Crossref]

Gonzalez-Ovejero, D.

D. Gonzalez-Ovejero, E. Martini, B. Loiseaux, C. Tripon-Canseliet, M. Mencagli, J. Chazelas, and S. Maci, “Basic properties of checkerboard metasurfaces,” IEEE Antennas Wireless Propag. Lett. 14, 406–409 (2015).
[Crossref]

Gossard, A. C.

H.-T. Chen, W. J. Padilla, J. M. O. Zide, A. C. Gossard, A. J. Taylor, and R. D. Averitt, “Active terahertz meta-material devices,” Nature 444, 597–600 (2006).
[Crossref] [PubMed]

Grischkowsky, D.

Hangyo, M.

Hibbins, A. P.

J. D. Edmunds, A. P. Hibbins, J. R. Sambles, and I. J. Youngs, “Resonantly inverted microwave transmissivity threshold of metal grids,” New J. Phys. 12, 063007 (2010).
[Crossref]

Highstrete, C.

Isozaki, A.

T. Kan, A. Isozaki, N. Kanda, N. Nemoto, K. Konishi, M. Kuwata-Gonokami, K. Matsumoto, and I. Shimoyama, “Spiral metamaterial for active tuning of optical activity,” Appl. Phys. Lett. 102, 221906 (2013).
[Crossref]

Ito, H.

Iwaszczuk, K.

Jepsen, P. U.

Jiang, L.

J. Y. Ou, E. Plum, L. Jiang, and N. I. Zheludev, “Reconfigurable photonic metamaterials,” Nano Lett. 11, 2142–2144 (2011).
[Crossref] [PubMed]

Kaiser, S.

T. Zentgraf, T. Meyrath, A. Seidel, S. Kaiser, H. Giessen, C. Rockstuhl, and F. Lederer, “Babinet’s principle for optical frequency metamaterials and nanoantennas,” Phys. Rev. B 76, 033407 (2007).
[Crossref]

Kan, T.

T. Kan, A. Isozaki, N. Kanda, N. Nemoto, K. Konishi, M. Kuwata-Gonokami, K. Matsumoto, and I. Shimoyama, “Spiral metamaterial for active tuning of optical activity,” Appl. Phys. Lett. 102, 221906 (2013).
[Crossref]

Kanda, N.

T. Kan, A. Isozaki, N. Kanda, N. Nemoto, K. Konishi, M. Kuwata-Gonokami, K. Matsumoto, and I. Shimoyama, “Spiral metamaterial for active tuning of optical activity,” Appl. Phys. Lett. 102, 221906 (2013).
[Crossref]

Kapitanova, P. V.

I. V. Shadrivov, P. V. Kapitanova, S. I. Maslovski, and Y. S. Kivshar, “Metamaterials controlled with light,” Phys. Rev. Lett. 109, 083902 (2012).
[Crossref] [PubMed]

Keiding, S.

Kempa, K.

K. Kempa, “Percolation effects in the checkerboard babinet series of metamaterial structures,” Phys. Status Solidi Rapid Res. Lett. 4, 218–220 (2010).
[Crossref]

Kieffer, J. C.

A. Cavalleri, Cs. Tóth, C. W. Siders, J. A. Squier, F. Ráksi, P. Forget, and J. C. Kieffer, “Femtosecond structural dynamics in VO2 during an ultrafast solid-solid phase transition,” Phys. Rev. Lett. 87, 237401 (2001).
[Crossref]

Kitano, M.

Y. Urade, Y. Nakata, T. Nakanishi, and M. Kitano, “Frequency-independent response of self-complementary checkerboard screens,” Phys. Rev. Lett. 114, 237401 (2015).
[Crossref] [PubMed]

F. Miyamaru, H. Morita, Y. Nishiyama, T. Nishida, T. Nakanishi, M. Kitano, and M. W. Takeda, “Ultrafast optical control of group delay of narrow-band terahertz waves,” Sci. Rep. 4, 4346 (2014).
[Crossref] [PubMed]

Y. Nakata, Y. Urade, T. Nakanishi, and M. Kitano, “Plane-wave scattering by self-complementary metasurfaces in terms of electromagnetic duality and Babinet’s principle,” Phys. Rev. B 88, 205138 (2013).
[Crossref]

Kivshar, Y. S.

I. V. Shadrivov, P. V. Kapitanova, S. I. Maslovski, and Y. S. Kivshar, “Metamaterials controlled with light,” Phys. Rev. Lett. 109, 083902 (2012).
[Crossref] [PubMed]

N. I. Zheludev and Y. S. Kivshar, “From metamaterials to metadevices,” Nat. Mater. 11, 917–924 (2012).
[Crossref] [PubMed]

Kong, J. A.

J. A. Kong, Electromagnetic Wave Theory, 2 (Wiley, 1990).

Konishi, K.

T. Kan, A. Isozaki, N. Kanda, N. Nemoto, K. Konishi, M. Kuwata-Gonokami, K. Matsumoto, and I. Shimoyama, “Spiral metamaterial for active tuning of optical activity,” Appl. Phys. Lett. 102, 221906 (2013).
[Crossref]

Kubo, N.

K. Okimura and N. Kubo, “Preparation of VO2 films with metal-insulator transition on sapphire and silicon substrates by inductively coupled plasma-assisted sputtering,” Jpn. J. Appl. Phys. 44, 1150–1153 (2005).
[Crossref]

Kuwata-Gonokami, M.

T. Kan, A. Isozaki, N. Kanda, N. Nemoto, K. Konishi, M. Kuwata-Gonokami, K. Matsumoto, and I. Shimoyama, “Spiral metamaterial for active tuning of optical activity,” Appl. Phys. Lett. 102, 221906 (2013).
[Crossref]

Landy, N. I.

Lederer, F.

T. Zentgraf, T. Meyrath, A. Seidel, S. Kaiser, H. Giessen, C. Rockstuhl, and F. Lederer, “Babinet’s principle for optical frequency metamaterials and nanoantennas,” Phys. Rev. B 76, 033407 (2007).
[Crossref]

Lee, M.

Loiseaux, B.

D. Gonzalez-Ovejero, E. Martini, B. Loiseaux, C. Tripon-Canseliet, M. Mencagli, J. Chazelas, and S. Maci, “Basic properties of checkerboard metasurfaces,” IEEE Antennas Wireless Propag. Lett. 14, 406–409 (2015).
[Crossref]

Lorenzen, D. L.

Losada, V.

J. D. Ortiz, J. D. Baena, V. Losada, F. Medina, R. Marques, and J. A. Quijano, “Self-complementary metasurface for designing narrow band pass/stop filters,” IEEE Microw. Wirel. Components Lett. 23, 291–293 (2013).
[Crossref]

Maci, S.

D. Gonzalez-Ovejero, E. Martini, B. Loiseaux, C. Tripon-Canseliet, M. Mencagli, J. Chazelas, and S. Maci, “Basic properties of checkerboard metasurfaces,” IEEE Antennas Wireless Propag. Lett. 14, 406–409 (2015).
[Crossref]

Marques, R.

J. D. Ortiz, J. D. Baena, V. Losada, F. Medina, R. Marques, and J. A. Quijano, “Self-complementary metasurface for designing narrow band pass/stop filters,” IEEE Microw. Wirel. Components Lett. 23, 291–293 (2013).
[Crossref]

Martini, E.

D. Gonzalez-Ovejero, E. Martini, B. Loiseaux, C. Tripon-Canseliet, M. Mencagli, J. Chazelas, and S. Maci, “Basic properties of checkerboard metasurfaces,” IEEE Antennas Wireless Propag. Lett. 14, 406–409 (2015).
[Crossref]

Maslovski, S. I.

I. V. Shadrivov, P. V. Kapitanova, S. I. Maslovski, and Y. S. Kivshar, “Metamaterials controlled with light,” Phys. Rev. Lett. 109, 083902 (2012).
[Crossref] [PubMed]

Matsumoto, K.

T. Kan, A. Isozaki, N. Kanda, N. Nemoto, K. Konishi, M. Kuwata-Gonokami, K. Matsumoto, and I. Shimoyama, “Spiral metamaterial for active tuning of optical activity,” Appl. Phys. Lett. 102, 221906 (2013).
[Crossref]

Medina, F.

J. D. Ortiz, J. D. Baena, V. Losada, F. Medina, R. Marques, and J. A. Quijano, “Self-complementary metasurface for designing narrow band pass/stop filters,” IEEE Microw. Wirel. Components Lett. 23, 291–293 (2013).
[Crossref]

Mencagli, M.

D. Gonzalez-Ovejero, E. Martini, B. Loiseaux, C. Tripon-Canseliet, M. Mencagli, J. Chazelas, and S. Maci, “Basic properties of checkerboard metasurfaces,” IEEE Antennas Wireless Propag. Lett. 14, 406–409 (2015).
[Crossref]

Meyrath, T.

T. Zentgraf, T. Meyrath, A. Seidel, S. Kaiser, H. Giessen, C. Rockstuhl, and F. Lederer, “Babinet’s principle for optical frequency metamaterials and nanoantennas,” Phys. Rev. B 76, 033407 (2007).
[Crossref]

Miyamaru, F.

Miyazaki, H.

Morin, F. J.

F. J. Morin, “Oxides which show a metal-to-insulator transition at the Neel temperature,” Phys. Rev. Lett. 3, 34 (1959).
[Crossref]

Morita, H.

F. Miyamaru, H. Morita, Y. Nishiyama, T. Nishida, T. Nakanishi, M. Kitano, and M. W. Takeda, “Ultrafast optical control of group delay of narrow-band terahertz waves,” Sci. Rep. 4, 4346 (2014).
[Crossref] [PubMed]

Nakanishi, T.

Y. Urade, Y. Nakata, T. Nakanishi, and M. Kitano, “Frequency-independent response of self-complementary checkerboard screens,” Phys. Rev. Lett. 114, 237401 (2015).
[Crossref] [PubMed]

F. Miyamaru, H. Morita, Y. Nishiyama, T. Nishida, T. Nakanishi, M. Kitano, and M. W. Takeda, “Ultrafast optical control of group delay of narrow-band terahertz waves,” Sci. Rep. 4, 4346 (2014).
[Crossref] [PubMed]

Y. Nakata, Y. Urade, T. Nakanishi, and M. Kitano, “Plane-wave scattering by self-complementary metasurfaces in terms of electromagnetic duality and Babinet’s principle,” Phys. Rev. B 88, 205138 (2013).
[Crossref]

Nakata, Y.

Y. Urade, Y. Nakata, T. Nakanishi, and M. Kitano, “Frequency-independent response of self-complementary checkerboard screens,” Phys. Rev. Lett. 114, 237401 (2015).
[Crossref] [PubMed]

Y. Nakata, Y. Urade, T. Nakanishi, and M. Kitano, “Plane-wave scattering by self-complementary metasurfaces in terms of electromagnetic duality and Babinet’s principle,” Phys. Rev. B 88, 205138 (2013).
[Crossref]

Nemoto, N.

T. Kan, A. Isozaki, N. Kanda, N. Nemoto, K. Konishi, M. Kuwata-Gonokami, K. Matsumoto, and I. Shimoyama, “Spiral metamaterial for active tuning of optical activity,” Appl. Phys. Lett. 102, 221906 (2013).
[Crossref]

Nihei, Y.

K. Okimura, Y. Sasakawa, and Y. Nihei, “X-ray diffraction study of electric field-induced metal-insulator transition of vanadium dioxide film on sapphire substrate,” Jpn. J. Appl. Phys. 45, 9200–9202 (2006).
[Crossref]

Nishida, T.

F. Miyamaru, H. Morita, Y. Nishiyama, T. Nishida, T. Nakanishi, M. Kitano, and M. W. Takeda, “Ultrafast optical control of group delay of narrow-band terahertz waves,” Sci. Rep. 4, 4346 (2014).
[Crossref] [PubMed]

Nishiyama, Y.

F. Miyamaru, H. Morita, Y. Nishiyama, T. Nishida, T. Nakanishi, M. Kitano, and M. W. Takeda, “Ultrafast optical control of group delay of narrow-band terahertz waves,” Sci. Rep. 4, 4346 (2014).
[Crossref] [PubMed]

O’Hara, J. F.

Okimura, K.

K. Okimura, Y. Sasakawa, and Y. Nihei, “X-ray diffraction study of electric field-induced metal-insulator transition of vanadium dioxide film on sapphire substrate,” Jpn. J. Appl. Phys. 45, 9200–9202 (2006).
[Crossref]

K. Okimura and N. Kubo, “Preparation of VO2 films with metal-insulator transition on sapphire and silicon substrates by inductively coupled plasma-assisted sputtering,” Jpn. J. Appl. Phys. 44, 1150–1153 (2005).
[Crossref]

Ortiz, J. D.

J. D. Ortiz, J. D. Baena, V. Losada, F. Medina, R. Marques, and J. A. Quijano, “Self-complementary metasurface for designing narrow band pass/stop filters,” IEEE Microw. Wirel. Components Lett. 23, 291–293 (2013).
[Crossref]

Ou, J. Y.

J. Y. Ou, E. Plum, L. Jiang, and N. I. Zheludev, “Reconfigurable photonic metamaterials,” Nano Lett. 11, 2142–2144 (2011).
[Crossref] [PubMed]

Padilla, W. J.

H. Tao, W. J. Padilla, X. Zhang, and R. D. Averitt, “Recent progress in electromagnetic metamaterial devices for terahertz applications,” IEEE J. Sel. Top. Quantum Electron. 17, 92–101 (2011).
[Crossref]

H.-T. Chen, W. J. Padilla, M. J. Cich, A. K. Azad, R. D. Averitt, and A. J. Taylor, “A metamaterial solid-state terahertz phase modulator,” Nat. Photonics 3, 148–151 (2009).
[Crossref]

H. Tao, N. I. Landy, C. M. Bingham, X. Zhang, R. D. Averitt, and W. J. Padilla, “A metamaterial absorber for the terahertz regime: design, fabrication and characterization,” Opt. Express 16, 7181–7188 (2008).
[Crossref] [PubMed]

H.-T. Chen, J. F. O’Hara, A. J. Taylor, R. D. Averitt, C. Highstrete, M. Lee, and W. J. Padilla, “Complementary planar terahertz metamaterials,” Opt. Express 15, 1084–1095 (2007).
[Crossref] [PubMed]

H.-T. Chen, W. J. Padilla, J. M. O. Zide, A. C. Gossard, A. J. Taylor, and R. D. Averitt, “Active terahertz meta-material devices,” Nature 444, 597–600 (2006).
[Crossref] [PubMed]

Plum, E.

J. Y. Ou, E. Plum, L. Jiang, and N. I. Zheludev, “Reconfigurable photonic metamaterials,” Nano Lett. 11, 2142–2144 (2011).
[Crossref] [PubMed]

Quijano, J. A.

J. D. Ortiz, J. D. Baena, V. Losada, F. Medina, R. Marques, and J. A. Quijano, “Self-complementary metasurface for designing narrow band pass/stop filters,” IEEE Microw. Wirel. Components Lett. 23, 291–293 (2013).
[Crossref]

Ráksi, F.

A. Cavalleri, Cs. Tóth, C. W. Siders, J. A. Squier, F. Ráksi, P. Forget, and J. C. Kieffer, “Femtosecond structural dynamics in VO2 during an ultrafast solid-solid phase transition,” Phys. Rev. Lett. 87, 237401 (2001).
[Crossref]

Rockstuhl, C.

T. Zentgraf, T. Meyrath, A. Seidel, S. Kaiser, H. Giessen, C. Rockstuhl, and F. Lederer, “Babinet’s principle for optical frequency metamaterials and nanoantennas,” Phys. Rev. B 76, 033407 (2007).
[Crossref]

Sambles, J. R.

J. D. Edmunds, A. P. Hibbins, J. R. Sambles, and I. J. Youngs, “Resonantly inverted microwave transmissivity threshold of metal grids,” New J. Phys. 12, 063007 (2010).
[Crossref]

Sasakawa, Y.

K. Okimura, Y. Sasakawa, and Y. Nihei, “X-ray diffraction study of electric field-induced metal-insulator transition of vanadium dioxide film on sapphire substrate,” Jpn. J. Appl. Phys. 45, 9200–9202 (2006).
[Crossref]

Seidel, A.

T. Zentgraf, T. Meyrath, A. Seidel, S. Kaiser, H. Giessen, C. Rockstuhl, and F. Lederer, “Babinet’s principle for optical frequency metamaterials and nanoantennas,” Phys. Rev. B 76, 033407 (2007).
[Crossref]

Shadrivov, I. V.

I. V. Shadrivov, P. V. Kapitanova, S. I. Maslovski, and Y. S. Kivshar, “Metamaterials controlled with light,” Phys. Rev. Lett. 109, 083902 (2012).
[Crossref] [PubMed]

Shimoyama, I.

T. Kan, A. Isozaki, N. Kanda, N. Nemoto, K. Konishi, M. Kuwata-Gonokami, K. Matsumoto, and I. Shimoyama, “Spiral metamaterial for active tuning of optical activity,” Appl. Phys. Lett. 102, 221906 (2013).
[Crossref]

Siders, C. W.

A. Cavalleri, Cs. Tóth, C. W. Siders, J. A. Squier, F. Ráksi, P. Forget, and J. C. Kieffer, “Femtosecond structural dynamics in VO2 during an ultrafast solid-solid phase transition,” Phys. Rev. Lett. 87, 237401 (2001).
[Crossref]

Singaraju, B. K.

C. E. Baum and B. K. Singaraju, “Generalization of Babinet’s principle in terms of the combined field to include impedance loaded aperture antennas and scatterers,” Interaction Note No. 217, Air Force Weapons Lab., Kirtland Air Force Base, NM87117 (1974).

Slobozhanyuk, A. P.

J. D. Baena, J. P. del Risco, A. P. Slobozhanyuk, S. B. Glybovski, and P. A. Belov, “Self-complementary meta-surfaces for linear-to-circular polarization conversion,” Phys. Rev. B 92, 245413 (2015).
[Crossref]

Squier, J. A.

A. Cavalleri, Cs. Tóth, C. W. Siders, J. A. Squier, F. Ráksi, P. Forget, and J. C. Kieffer, “Femtosecond structural dynamics in VO2 during an ultrafast solid-solid phase transition,” Phys. Rev. Lett. 87, 237401 (2001).
[Crossref]

Strikwerda, A. C.

Takano, K.

Takeda, M. W.

Tao, H.

H. Tao, W. J. Padilla, X. Zhang, and R. D. Averitt, “Recent progress in electromagnetic metamaterial devices for terahertz applications,” IEEE J. Sel. Top. Quantum Electron. 17, 92–101 (2011).
[Crossref]

H. Tao, N. I. Landy, C. M. Bingham, X. Zhang, R. D. Averitt, and W. J. Padilla, “A metamaterial absorber for the terahertz regime: design, fabrication and characterization,” Opt. Express 16, 7181–7188 (2008).
[Crossref] [PubMed]

Taylor, A. J.

H.-T. Chen, W. J. Padilla, M. J. Cich, A. K. Azad, R. D. Averitt, and A. J. Taylor, “A metamaterial solid-state terahertz phase modulator,” Nat. Photonics 3, 148–151 (2009).
[Crossref]

H.-T. Chen, J. F. O’Hara, A. J. Taylor, R. D. Averitt, C. Highstrete, M. Lee, and W. J. Padilla, “Complementary planar terahertz metamaterials,” Opt. Express 15, 1084–1095 (2007).
[Crossref] [PubMed]

H.-T. Chen, W. J. Padilla, J. M. O. Zide, A. C. Gossard, A. J. Taylor, and R. D. Averitt, “Active terahertz meta-material devices,” Nature 444, 597–600 (2006).
[Crossref] [PubMed]

Tokuda, Y.

Tóth, Cs.

A. Cavalleri, Cs. Tóth, C. W. Siders, J. A. Squier, F. Ráksi, P. Forget, and J. C. Kieffer, “Femtosecond structural dynamics in VO2 during an ultrafast solid-solid phase transition,” Phys. Rev. Lett. 87, 237401 (2001).
[Crossref]

Tripon-Canseliet, C.

D. Gonzalez-Ovejero, E. Martini, B. Loiseaux, C. Tripon-Canseliet, M. Mencagli, J. Chazelas, and S. Maci, “Basic properties of checkerboard metasurfaces,” IEEE Antennas Wireless Propag. Lett. 14, 406–409 (2015).
[Crossref]

Urade, Y.

Y. Urade, Y. Nakata, T. Nakanishi, and M. Kitano, “Frequency-independent response of self-complementary checkerboard screens,” Phys. Rev. Lett. 114, 237401 (2015).
[Crossref] [PubMed]

Y. Nakata, Y. Urade, T. Nakanishi, and M. Kitano, “Plane-wave scattering by self-complementary metasurfaces in terms of electromagnetic duality and Babinet’s principle,” Phys. Rev. B 88, 205138 (2013).
[Crossref]

van Exter, M.

Youngs, I. J.

J. D. Edmunds, A. P. Hibbins, J. R. Sambles, and I. J. Youngs, “Resonantly inverted microwave transmissivity threshold of metal grids,” New J. Phys. 12, 063007 (2010).
[Crossref]

Zalkovskij, M.

Zentgraf, T.

T. Zentgraf, T. Meyrath, A. Seidel, S. Kaiser, H. Giessen, C. Rockstuhl, and F. Lederer, “Babinet’s principle for optical frequency metamaterials and nanoantennas,” Phys. Rev. B 76, 033407 (2007).
[Crossref]

Zhang, X.

H. Tao, W. J. Padilla, X. Zhang, and R. D. Averitt, “Recent progress in electromagnetic metamaterial devices for terahertz applications,” IEEE J. Sel. Top. Quantum Electron. 17, 92–101 (2011).
[Crossref]

H. Tao, N. I. Landy, C. M. Bingham, X. Zhang, R. D. Averitt, and W. J. Padilla, “A metamaterial absorber for the terahertz regime: design, fabrication and characterization,” Opt. Express 16, 7181–7188 (2008).
[Crossref] [PubMed]

Zheludev, N. I.

N. I. Zheludev and Y. S. Kivshar, “From metamaterials to metadevices,” Nat. Mater. 11, 917–924 (2012).
[Crossref] [PubMed]

J. Y. Ou, E. Plum, L. Jiang, and N. I. Zheludev, “Reconfigurable photonic metamaterials,” Nano Lett. 11, 2142–2144 (2011).
[Crossref] [PubMed]

Zide, J. M. O.

H.-T. Chen, W. J. Padilla, J. M. O. Zide, A. C. Gossard, A. J. Taylor, and R. D. Averitt, “Active terahertz meta-material devices,” Nature 444, 597–600 (2006).
[Crossref] [PubMed]

Appl. Phys. Lett. (1)

T. Kan, A. Isozaki, N. Kanda, N. Nemoto, K. Konishi, M. Kuwata-Gonokami, K. Matsumoto, and I. Shimoyama, “Spiral metamaterial for active tuning of optical activity,” Appl. Phys. Lett. 102, 221906 (2013).
[Crossref]

IEEE Antennas Wireless Propag. Lett. (1)

D. Gonzalez-Ovejero, E. Martini, B. Loiseaux, C. Tripon-Canseliet, M. Mencagli, J. Chazelas, and S. Maci, “Basic properties of checkerboard metasurfaces,” IEEE Antennas Wireless Propag. Lett. 14, 406–409 (2015).
[Crossref]

IEEE J. Sel. Top. Quantum Electron. (1)

H. Tao, W. J. Padilla, X. Zhang, and R. D. Averitt, “Recent progress in electromagnetic metamaterial devices for terahertz applications,” IEEE J. Sel. Top. Quantum Electron. 17, 92–101 (2011).
[Crossref]

IEEE Microw. Wirel. Components Lett. (1)

J. D. Ortiz, J. D. Baena, V. Losada, F. Medina, R. Marques, and J. A. Quijano, “Self-complementary metasurface for designing narrow band pass/stop filters,” IEEE Microw. Wirel. Components Lett. 23, 291–293 (2013).
[Crossref]

J. Opt. Soc. Am. B (1)

Jpn. J. Appl. Phys. (2)

K. Okimura, Y. Sasakawa, and Y. Nihei, “X-ray diffraction study of electric field-induced metal-insulator transition of vanadium dioxide film on sapphire substrate,” Jpn. J. Appl. Phys. 45, 9200–9202 (2006).
[Crossref]

K. Okimura and N. Kubo, “Preparation of VO2 films with metal-insulator transition on sapphire and silicon substrates by inductively coupled plasma-assisted sputtering,” Jpn. J. Appl. Phys. 44, 1150–1153 (2005).
[Crossref]

Nano Lett. (1)

J. Y. Ou, E. Plum, L. Jiang, and N. I. Zheludev, “Reconfigurable photonic metamaterials,” Nano Lett. 11, 2142–2144 (2011).
[Crossref] [PubMed]

Nat. Mater. (1)

N. I. Zheludev and Y. S. Kivshar, “From metamaterials to metadevices,” Nat. Mater. 11, 917–924 (2012).
[Crossref] [PubMed]

Nat. Photonics (1)

H.-T. Chen, W. J. Padilla, M. J. Cich, A. K. Azad, R. D. Averitt, and A. J. Taylor, “A metamaterial solid-state terahertz phase modulator,” Nat. Photonics 3, 148–151 (2009).
[Crossref]

Nature (1)

H.-T. Chen, W. J. Padilla, J. M. O. Zide, A. C. Gossard, A. J. Taylor, and R. D. Averitt, “Active terahertz meta-material devices,” Nature 444, 597–600 (2006).
[Crossref] [PubMed]

New J. Phys. (1)

J. D. Edmunds, A. P. Hibbins, J. R. Sambles, and I. J. Youngs, “Resonantly inverted microwave transmissivity threshold of metal grids,” New J. Phys. 12, 063007 (2010).
[Crossref]

Opt. Express (4)

Phys. Rev. B (3)

T. Zentgraf, T. Meyrath, A. Seidel, S. Kaiser, H. Giessen, C. Rockstuhl, and F. Lederer, “Babinet’s principle for optical frequency metamaterials and nanoantennas,” Phys. Rev. B 76, 033407 (2007).
[Crossref]

J. D. Baena, J. P. del Risco, A. P. Slobozhanyuk, S. B. Glybovski, and P. A. Belov, “Self-complementary meta-surfaces for linear-to-circular polarization conversion,” Phys. Rev. B 92, 245413 (2015).
[Crossref]

Y. Nakata, Y. Urade, T. Nakanishi, and M. Kitano, “Plane-wave scattering by self-complementary metasurfaces in terms of electromagnetic duality and Babinet’s principle,” Phys. Rev. B 88, 205138 (2013).
[Crossref]

Phys. Rev. Lett. (4)

Y. Urade, Y. Nakata, T. Nakanishi, and M. Kitano, “Frequency-independent response of self-complementary checkerboard screens,” Phys. Rev. Lett. 114, 237401 (2015).
[Crossref] [PubMed]

F. J. Morin, “Oxides which show a metal-to-insulator transition at the Neel temperature,” Phys. Rev. Lett. 3, 34 (1959).
[Crossref]

I. V. Shadrivov, P. V. Kapitanova, S. I. Maslovski, and Y. S. Kivshar, “Metamaterials controlled with light,” Phys. Rev. Lett. 109, 083902 (2012).
[Crossref] [PubMed]

A. Cavalleri, Cs. Tóth, C. W. Siders, J. A. Squier, F. Ráksi, P. Forget, and J. C. Kieffer, “Femtosecond structural dynamics in VO2 during an ultrafast solid-solid phase transition,” Phys. Rev. Lett. 87, 237401 (2001).
[Crossref]

Phys. Status Solidi Rapid Res. Lett. (1)

K. Kempa, “Percolation effects in the checkerboard babinet series of metamaterial structures,” Phys. Status Solidi Rapid Res. Lett. 4, 218–220 (2010).
[Crossref]

Sci. Rep. (1)

F. Miyamaru, H. Morita, Y. Nishiyama, T. Nishida, T. Nakanishi, M. Kitano, and M. W. Takeda, “Ultrafast optical control of group delay of narrow-band terahertz waves,” Sci. Rep. 4, 4346 (2014).
[Crossref] [PubMed]

Other (2)

J. A. Kong, Electromagnetic Wave Theory, 2 (Wiley, 1990).

C. E. Baum and B. K. Singaraju, “Generalization of Babinet’s principle in terms of the combined field to include impedance loaded aperture antennas and scatterers,” Interaction Note No. 217, Air Force Weapons Lab., Kirtland Air Force Base, NM87117 (1974).

Cited By

OSA participates in Crossref's Cited-By Linking service. Citing articles from OSA journals and other participating publishers are listed here.

Alert me when this article is cited.


Figures (3)

Fig. 1
Fig. 1 Principles of Babinet-invertible metasurface. (a) Off state. (b) Babinet-inverted structure. Note that the polarization of the incident wave is orthogonal to that in the off state. (c) On state. The vectors E , H , and k indicate the electric field, the magnetic field, and the wavevector of the incident plane waves, respectively.
Fig. 2
Fig. 2 (a) Babinet-invertible metasurface design. The parameters are as follows: a = 75µm, g = 5µm, u = 15µm, and d = 32µm. The broken lines indicate the area where the Al structures overlap the VO2. (b) Calculated g dependence of the on-off ratio of the power transmission at the peak and dip frequencies and their frequency difference. (c) Photograph of fabricated metasurface. The exposed regions of the VO2 patches are digitally colored in turquoise for clarity.
Fig. 3
Fig. 3 Measured transmission coefficient spectra at T = 300 and 370K: (a) amplitude transmission spectra and (b) phase shift spectra.

Equations (1)

Equations on this page are rendered with MathJax. Learn more.

t ˜ ( ω ) + t ˜ c ( ω ) = 1 ,

Metrics