The plasmonic nanostructures are widely used to design sensors with improved capabilities. The position of the localized surface plasmon resonance (LSPR) is part of their characteristics and deserves to be specifically studied, according to its importance in sensor tuning, especially for spectroscopic applications. In the visible and near infra-red domain, the LSPR of an array of nano-gold-cylinders is considered as a function of the diameter, height of cylinders and the thickness of chromium adhesion layer and roughness. A numerical experience plan is used to calculate heuristic laws governing the inverse problem and the propagation of uncertainties. Simple linear formulae are deduced from fitting of discrete dipole approximation (DDA) calculations of spectra and a good agreement with various experimental results is found. The size of cylinders can be deduced from a target position of the LSPR and conversely, the approximate position of the LSPR can be simply deduced from the height and diameter of cylinders. The sensitivity coefficients and the propagation of uncertainties on these parameters are evaluated from the fitting of 15500 computations of the DDA model. The case of a grating of nanodisks and of homothetic cylinders is presented and expected trends in the improvement of the fabrication process are proposed.
© 2013 Optical Society of America
Arrays of metallic nanostructures have been extensively studied as they are known to be efficient and tunable [1, 2]. The underlying physical phenomenon is the localized surface plasmon resonance (LSPR). According to Maier, “Localized surface plasmons are non-propagating excitations of the conduction electrons of metallic nanostructures coupled to the electromagnetic field. . . The curved surface of the particles exerts an effective restoring force of the driven electrons, so that a resonance can arise, leading to field amplification both inside and in the near-field zone outside the particle.” .
The spectral position of the LSPR λ0(LSPR) can therefore be tuned by modifying the shape and size of the nanoparticles and be adapted to the specific excitation of molecules deposited on the nanoparticle surface. Obvious applications of plasmonic devices are biosensors. A periodic arrangement of nanoparticles is used to increase the sensitivity of the biosensor. The prolate and oblate exhibit LSPRs which are related to their asymmetry, leading to a distribution of energy in different LSPR modes . Coupling between transverse and longitudinal LSPR occurs. To prevent this effect which could decrease the efficiency of the biosensor, arrays of gold cylindric nanoparticles have been extensively studied [4–10]. In that papers, the tuning of the LSPR has been proved by varying the diameter of nanocylinders or seldom their height. In the investigated domain of wavelengths, some linear behaviors can be observed when the characteristic sizes of cylindrical nanoparticles were varied.
Based on those results, we propose a basic approach of the inverse problem to deduce analytical laws for the LSPR and then to deduce propagation of uncertainties and tolerance study for the fabrication of nano-gold cylinder based biosensors.
The inverse problem usually goes through an initial stage of modeling of the phenomenon, called direct problem which describes how the parameters of the model translate into experimentally observable LSPR shifts. The key parameters of the problem are identified and also the most likely approximation of their behavior for a given list of λ0(LSPR) (Sec. 2). Then, obtained from systematic numerical experiments, the approach will be to deduce the analytical function giving the LSPR position as a function of the key parameters. This resolution can be done analytically, if the relationship between parameters and λ0(LSPR) is an invertible function of the key parameters (Sec. 3). The result helps to obtain an heuristic formula for λ0(LSPR) within the investigated domain of parameters (Sec. 4). The propagation of uncertainties and therefore the tolerance of fabrication of such nano-device are deduced. A final validation of the solution of the inverse problem with some experimental data is finally proposed (Sec. 5).
The typical parameters of the array of nanocylinders are firstly discussed before presenting the model of the interaction between light and array of nanocylinders. Then it is used within a systematic study of the geometric parameters within domains of variation of previously published experimental data.
2. The array of nanocylinders, experimental uncertainties
The Fig. 1 shows a schematic of the array of nanocylinders. All the parameters related to the experiments can be found in . A grating of gold nanocylinders is deposited on a glass substrate. The distance between cylinders P is supposed to be fixed to 200 nm. Let us note that the periodicity of the grating may influence the detected position of the LSPR [5, 11], in particular in the case of an homogeneous-evanescent switch of a diffracted order [12, 13]. Experimental studies have shown that a variation of the period P + D = 200 ± 50 nm, leads to a LSPR shift lower than 20 nm [14, p. 67].  observed a redshift of 14 nm observed when the interparticle distance P was varied from 200 to 300 nm. Therefore the influence of the experimental uncertainty on this parameter is neglected on the contrary of those on the height and on the diameter of nanocylinders. We focus on the systematic study of the position of LSPR as a function of the diameter D and height h of the gold nanocylinders. The thickness e of the chromium adhesion layer and the roughness of surfaces are included in the model [15, 16].
The nanostructures are deposited on a glass substrate through electron beam lithography (EBL) and lift-off techniques. To achieve EBL, a 30 kV Hitachi S-3500N scanning electron microscope (SEM) equipped with nanometer pattern generation system (NPGS, by J.C. Nabity) are used . The SEM images [4, 5, 8, 14, 18] reveal the experimental sources of uncertainties on the geometrical parameters in the process of fabrication:
- Height (h): the maximum uncertainty is δh = ±2 nm. This value is due to both the roughness and the process of metal deposition. The SEM images and AFM (Atomic Force Microscopy) scans reveal a RMS (root of mean square) lower than one nanometer .
- Thickness (e): the maximum uncertainty is also δe ± 2 nm, but may depend on the thickness of the intermediate layer.
- Diameter (D): the maximum uncertainty is δD = ±20 nm. This value is relative to both the fabrication and the resolution of the SEM  and to a drift of diameter and shape on the whole grating. This last source of uncertainty is evaluated through statistics on the SEM images and is compatible with that found in literature .
In the following, the model is used to investigate the propagation of uncertainties on the position of the LSPR. The experimental uncertainties are highly dependent on the process of fabrication of the nanostructures. Among all parameters the roughness of gold nanostructures varies when annealing of sample is used. However, the proposed method remains functional provided the uncertainties are experimentally characterized.
The illumination comes parallel to the cylinder axis and is linearly polarized. The detection of the LSPR is carried out in transmission, in the same direction (in the specular direction) and in far field. Spectroscopic studies are experimentally performed and the maximum of extinction over the incoming wavelengths λ0 is supposed to reveal the LSPR position . It is commonly admitted that the nanostructures scatters and absorbs a part of the incoming light and that the detected intensity in transmission reveals the extinction of the illumination by the sample [1, 22].
3. Model of the interaction of light with nanocylinders array
The fabrication process of nanodevices has been continuously improved and more control and precision were achieved [23, 24] but a residual roughness remains on the nanostructures. Indeed, the process of deposition of metal on the substrate is subject to incertitudes on the size of the nanostructures that are generally rough [5, 6, 8, 25, 26]. Usually, roughness is neglected in the models because many have an inability to take into account.
Moreover, a thin intermediate layer (Cr, Ti, or Ni typically) is used to stick gold on substrate. This adhesion layer shifts and broadens the LSPR peak [25, 27] as well as the Surface Plasmon Resonance of thin films [15, 28, 29]. The critical role of the adhesion layer is undeniable [26, 30] even if some theoretical studies revealed that a chromium layer with thickness smaller than 10 nm only slightly influences the LSPR position for an array of nano-cylinders . On the other hand, the adhesion layer plays a crucial role on the plasmonic fluorescence enhancement .
Therefore, both roughness and adhesion layer should not be neglected in a first approach. The need to describe the roughness numerical models restricts the choice of methods, even if some conventional methods were modified to describe this property of scattering objects: finite difference time domain (FDTD) , coupled wave method (CWM) , finite element method (FEM) [33, 34], boundary element method (BEM)  for which the meshing of the rough surface may be critical for computation. In  was claimed that a roughness of 1 nm produces negligible disturbance of the surface plasmon, but authors also underlined that the imperfection of the fabrication process may produce very rough surfaces and therefore could induce notable variations in the computed properties of localized plasmons between smooth and rough surfaces, and therefore with experiments. However the most famous (and the oldest) method used to describe light-matter interaction with nanoparticles with irregular shape and sometimes rough is probably the discrete dipole approximation (DDA) [18,36–42].
DDA was firstly developed by Devoe [43, 44] and Purcell . The main idea is to discretize the nanoparticle into a set of N elements or dipoles with polarizabilities αj, located at rj. Each dipole has a polarization Pj = αjEj, where Ej is the electric field at rj induced by the incident wave and the sum of the dielectric fields induced by interaction with other dipoles. Consequently, a system of complex linear equations must be solved to find polarizations Pj and evaluate the extinction cross section following :22], k0 = 2π/λ0 the modulus of the wave vector and E0 the amplitude, of the illumination monochromatic plane wave. ℑ(.) is the imaginary part of a complex number. Cext is written under the assumption of linearly polarized incident light . The method was extended to periodic structures by Markel  and Chaumet [41, 47].
Investigation of the validity criterion of discrete dipole approximation method (DDA) confirmed than that method is suitable for highly irregular particles, when many other approaches are not available . Comparison with experiments reveals a high sensitivity of results with dielectric functions of metal . Nanoparticles with arbitrary shapes where modeled for extinction and Raman spectroscopy applications  and the influence of porosity of thin cylinders was recently investigated with DDA . In a recent paper, the comparisons of numerical results with two series of experimental data reveal that modeling the roughness of samples gives better agreement  and propose therefore, an alternative to the approximative knowledge of permittivity, for the explanation of the decay between experiments and calculations . Therefore, we propose to use the DDA for the following study.
The Fortran code DDSCAT 7.1, developed by Draine and Flatau, is used for calculating extinction of light by irregular particles based on the DDA . DDSCAT offers the possibility of editing new shapes. Therefore, to handle with roughness, a uniform probability law is used to remove or to add a dipole from/to the surface, or to keep it unchanged (Fig. 2) . Therefore, the root of mean square roughness is , that is close to the 3 RMS resulting from the lithography process that can be observed in MEB images of samples. The adhesion layer is also discretized as shown in Fig. 2.
The inter-dipole distance d = 2 nm is smaller than 2.6 nm that ensured the validity of the calculations in . The target precision for the inversion of the matrix of coupling between dipoles is 10−3. The magnitude of the electric field at distance r from any dipole decreases as a polynomial function of 1/r. The factor exp [−(γk0r)4] was introduced to vanish the coupling between remote dipoles in a periodic lattice (with k0 = 2π/λ0 the modulus of the illumination wave vector) and therefore to increase the speed and accuracy of computation . γ can be therefore seen as a cutoff parameter which smoothly suppresses the influence of far dipoles in periodic structures. In the present case, γ = 0.1 is chosen to achieve both sufficient accuracy in the investigated size range of parameters, and a reasonable computational time (less than one hour). Indeed, the computation of spectrums in the range 550 nm to 850 nm of wavelength requires 31 evaluations of the model, if a precision of 10 nm is supposed to be sufficient for the computation of the LSPR spectral position.
The DDA is based on the discretization of materials, and therefore including the thick substrate in the model would require computational time. Consequently, the surrounding medium is modeled by an effective medium with relative permittivity εeff[18, 53] equal to the mean of that of the glass substrate  and that of air (Eq. (2)). The relative permittivity of glass (1.432 = 2.04) is considered as constant on the whole investigated domain of wavelengths (λ0 ∈ [550, 850] nm).
This formulation is also known in optics as the Geometrical Effective Medium Approximation (GEMA) which was developed for absorbing multilayer structures  and used to retrieve unknown experimental data from Turbadar’s measurements of reflectance of thin aluminum layers .
The effective medium approximation may induce a blue-shift of the LSPR  but the comparison with other theoretical results may help to validate the proposed model of effective medium. We first compare DDA results to computations from Finite Difference Time Domain (FDTD) method . In that reference, no roughness was introduced, the surface of cylinders was smooth, D = 100 nm and h = 50 nm. The period of the grating was D + P = 300 nm with P = 200 nm (Fig. 1). The relative permittivities of metals were found in the same references [56, 57] and the nanostructures were deposited on a glass substrate. The location of the LSPR in the absence of Cr adhesion layer occurs at λ0 = 586 nm with FDTD and λ0 = 590 nm with DDA. Therefore in the investigated domain of parameters, the effective medium seems to be a usable approximation.
The relative permittivities of chromium and gold are the bulk ones [56, 57]. The gold and chromium relative permittivity from  and  are plotted in Figs. 3 and 4. For gold, the Johnson and Christy data are chosen for their smoother behavior within the investigated wavelengths domain. A cubic spline is used to get the appropriate discretization of the dispersion curves with wavelength step of 10 nm. The result takes advantage of the continuity of derivative compared to a linear fitting of the reference data.
Chromium is more absorbing than gold and therefore the extinction spectrum is broadened and attenuated for surface plasmon resonance (SPR) [15,58–60] and localized surface plasmon resonance (LSPR) [25–27,59]. These parameters are also subject to uncertainties and the position of the LSPR λ0(LSPR) = λ0(max(Cext)) could depend on them [39, 49] but their numerical values are unknown in our case.
Therefore the final validation of the results of the proposed method by comparison with series of experimental data remains the only alternative.
To perform a parametric study, the discretization of the parameter space (D, h, eλ0) must be determined, by a first evaluation of the propagation of experimental uncertainties through the numerical model. The target is the position of the LSPR.
4. Discretization and key parameters
The experimental uncertainties mentioned above (section 2) can help to define the step size of D, h, e and λ0 in order to maintain the computational time of the parametric study in a reasonable range and to obtain significant results. For this, we compute the propagation of experimental uncertainties through the model to check their influence on the shift of the LSPR. Two diameters are considered for this evaluation with the above described model: D = 100 nm and D = 200 nm, near the boundaries of the investigated domain of the parametric study. The height of cylinders is the reference in experiments h = 50 nm . A step of 10 nm is used for the computations of the spectrum Cext (λ0). The cylinders are supposed to have smooth surfaces. The corresponding uncertainty on the position of LSPR (λ0(LSPR)) is therefore ±5 nm in the numerical calculations. This approach corresponds to the evaluation of the partial derivative of the function λ0(LSPR)(D, h, e, RMS) around typical values in the hyperspace of parameters.
The results in Table 1 show that h and D are key parameter for λ0(LSPR) as well as the roughness. The influence of the nanometric layer of chromium is less critical for the position of LSPR  than on the damping of the resonance and therefore on the sensitivity of the biosensor . The roughness cannot be neglected for the smallest diameter.
The combined uncertainty uB(λ0(LSPR)) on the LSPR shift can therefore be evaluated from the above uncertainties of type B , by considering a priori uniform law of probability within the above intervals and no correlation between these parameters. The following results are obtained:
In both cases, uncertainties may produce a shift greater than ±20 nm within the investigated range of diameters. The combined uncertainty is stable, even if the sensitivity to each source of uncertainty differs. Consequently, the influence of the experimental uncertainties on the position of the LSPR can be observed considering a sampling step of 10 nm for λ0. The corresponding uncertainty on the position of LSPR (λ0(LSPR)) is therefore ±5 nm in the numerical calculations. No further fitting of the extinction cross section Cext (λ0) curve is used. The evaluation of the experimental uncertainty (Eqs. (3) – (4)) is used in the following for the plot of experimental data. The computation of the position of the LSPR requires 31 computations of the extinction cross-section Cext for λ0 ∈ [550;850] nm. The rough sample is considered in the following.
The numerical experience plan consists in nested loops on D, h, e, λ0. Table 2 gives the intervals and the discretization step for all parameters. The total number of computations is N = 15500.
The N computations being realized on a computer with 30 processors, a database of results can be exploited. This approach is far from the optimization of the nanostructures which requires a specific optimization method for computational time sparing, to get the best parameters set [42, 62, 63]. The following establishment of an heuristic law governing the LSPR is based on the least square fitting of the database, using information on the critical parameters. The database obtained from the experience plan contains 500 simulations of the position of the LSPR for different gratings of nanocylinders.
5. Heuristic law for λ0(LSPR)
Some papers were dedicated to a systematic study of the optical properties (absorption, extinction or scattering) of nanoparticles [25,38–40,49]. All these studies are direct parametric studies and reveal the dependance of the LSPR of nanoparticles on the various parameters of the problem. In that studies, the position of the LSPR as a function of the aspect ratio, diameter or length of the nanoparticles was observed but never exploited through an inverse problem procedure .
A first analysis of the 500 computed spectra confirms that, with or without roughness, a chromium adhesion layer e lower than 6 nm produces only a shift of the LSPR lower than 20 nm. A theoretical study  and our results show that including the adhesion layer blueshifts the LSPR for small diameters (D = 100 nm). Increasing the diameter D or decreasing the height h of cylinders redshift the LSPR [18, 25]. The same behavior was observed for smooth nanodisks with D = 175 nm, h ranged from 10 nm to 150 nm .
Figure 5 shows a quasi-linear behavior of the relation between D and h for a given LSPR wavelength. The selection of the pairs of (D,h) corresponding to a given λ0(LSPR) = λ0(max(Cext)) are fitted with an affine function by minimizing the least square residue . The method uses a robust fit of the results of the parametric study. The algorithm uses iteratively reweighted least squares with the bisquare weighting function (Matlab). The resulting class of slope and intercept can then be fitted with an affine function of the LSPR wavelength λ0(LSPR):
The resulting heuristic law is deduced directly from the parametric study: a steady position of the LSPR is observed if the Eq. (5) between D (nm) and h (nm) is satisfied. This law is deduced from the least square fitting of the results of the parametric study, simply by computing the slope and the intercept of D as a function of h for each LSPR position, and then by finding the linear dependence of a and b on the LSPR position λ0(LSPR). A similar approach was used to characterize the near-field optical microscopes and the evanescent near-field around nanostructures [13, 66].
The values of ai and bi and their dispersion are given in Table 3.
Equation (5) is the solution of the inverse problem as it enables to calculate the geometrical parameter D for a target wavelength of LSPR. If h should be calculated as a function of λ0(LSPR), Eq. (6):
Figure 5 shows the plots of Eq. (5), superimposed on the data of the experience plan. The linear behavior of D as a function of h is dependent on the LSPR position. Equation (5) helps to determine the geometrical parameters (D and h) of the biosensor to adjust the LSPR to a given wavelength. The domain of validity of this law is the hypercube defined in Table 2 considering rough structures. Equation (5) gives a function which reciprocal can be calculated for deducing the position of the LSPR as a function of D and h.
A class of parameters can be therefore deduced from the formula (5), (6) and (7) and could help to design the biosensor. The formula (7) can also be used to calculate the propagation of experimental uncertainties for the LSPR position and therefore to evaluate the tolerance of fabrication of such device . Before going further, a validation of the proposed affine approximations must be proposed by comparison with experimental data.
5.1. Validation by comparison with experimental data
A comparison of the heuristic law (Eq. (7)) and experimental data in  shows a good agreement (Fig. 6). The values of h for the red curve are slightly lower than the experimental expected value by considering free height h. This behavior is coherent with the fact that the shape of nanoparticles is not exactly a cylinder but rather a smooth island of gold, especially for small diameters and heights.
The comparison with experimental data obtained by varying the height of cylinders (from ), shows also a good agreement for D = 100 nm (Fig. 7). The red curve is obtained for the best fitting of the experimental data by considering free diameter D. The corresponding values of D are close to the experimental value of D according to its uncertainty.
The two comparisons with experimental data for various values of h and D can be considered as hard tests of validity. The agreement of numerical and experimental results is satisfying and is coherent with the properties of the process of deposition of gold on substrate. Moreover the results show that the effective permittivity of the surrounding medium and the gold and chromium permittivities can be used to describe accurately the biosensor within the range of parameters.
In Ref.  the best Raman signal enhancement was obtained for the LSPR position exactly between the excitation wavelength λ0 and the Raman wavelength λR related to the band of interest of the probe molecule observed. Félidj et al. proposed to adjust the LSPR at the mean value of both wavelengthes. For excitation at λ0 = 632.8 nm and a Raman wavelength λR = 685 nm (BPE band at 1200 cm−1), the best LSPR position was found to be located at 659 nm. For the first order, the corresponding nanocylinder diameter was found to be close to 130 nm. The heuristic law gives D = 133 ± 3 nm for h = 50 nm and u(h) = ±2 nm. The second experience uses illumination at λ0 = 785 nm. Therefore λR = 867 nm and the LSPR is tuned to 826 nm. Formula (5) gives D = 256±6 nm, which is closer to the measured value of the best SERS gain obtained for D = 220 nm than the announced target (300 nm) in . The predictive ability of the heuristic law which describes the relationship between the LSPR position λ0(LSPR), D and h seems to be valid in the whole domain of parameters given in Table 1. To illustrate the possible use of this law, we investigate some specific geometries before evaluating the propagation of uncertainties.
5.2. Case of homothetic cylinders
Equation (7) seems to be a good approximation of the variation of the LSPR as a function of the geometrical parameters D and h, for a grating of rough gold cylinders with adhesion layer (e = 2 nm) and P = 200 nm (Fig. 1). The specific case of homothetic cylinders with h = D, removes a degree of freedom and leads to a simpler formula, with a1, a2, b1, b2 given in Table 3:
This formula is strictly valid in the interval h = D ranging from 50 to 70 nm, by cons it should still be checked for larger heights.
5.3. Case of nanodisks
Asymptotic form of λ0(LSPR) could be of interest especially for specific aspect ratio of the cylinder. For example, for nanodiscs (h << D), the position of the LSPR can be deduced from the series of Eq. (7).Table 3.
This equation confirms that the correction induced by the height assuming a small aspect ratio h/D is a blueshift of the LSPR, whatever are the diameters D. These formula can be used to select the best parameters for a given LSPR position. Figure 8 shows the plots of the position of the LSPR as a function of the aspect ratio D/h of the cylinder. The linear behavior can be compared to that observed for nanorods  for a wider range of aspect-ratio. This confirms the good behavior of the model in the range of parameters.
Another interest of these simple laws is the fact that propagation of uncertainties of the fabrication process can be evaluated directly, and therefore, the sensitivity analysis of LSPR position on the geometrical parameters h and D can be deduced, at least within the investigated domain of geometrical parameters and wavelengths. This is investigated in what follows.
5.4. Sensitivity of LSPR to uncertainties on size parameters
The propagation of uncertainties and the sensitivity analysis of a process or a physical phenomenon helps to improve the fabrication process of any device, by exhibiting the parameters that should be controlled first. Indeed the identification of critical parameters which uncertainty should be reduced is relevant, for a challenging improvement of technology.
First, the propagation of experimental uncertainties of fabrication can be deduced from the partial derivatives of λ0(LSPR)(D, h) (Eq. (7)). The uncertainty on λ0(LSPR) is deduced form the experimental uncertainties on D (u(D)) and h (u(h)) [61, 5.1.2]:Table 3 Knowing the experimental uncertainties on h and D, the uncertainty on the LSPR can be deduced. The sensitivity coefficients Sh and SD can be used to evaluate the effect of the experimental dispersion of values of D and h around a mean value. They contribute to the improvement of the uncertainty evaluation of the LSPR position given in Eqs. (3) – (4). For D = 100 nm and D = 200 nm, u(λ0(LSPR)) ≈ 27 nm and 28 nm respectively. The study of the properties of SD and Sh gives insight on the sensitivity of the uncertainty u(λ0(LSPR)) to uncertainties on D and h. The balance between the two terms of the sum in Eq. (11) could give information on the critical process that needs to be improved in priority.
The plot of SD (Fig. 9) show a slow decreasing of the sensitivity with h. The mean sensitivity of u(λ0(LSPR)) on D is therefore about 1.45 in the considered range of parameters. The same behavior is exhibited in Fig. 10, |Sh| decreases with h. The mean value of the sensitivity is around −4 and decreases with D. In terms of uncertainties, the weight of each term in the sum in Eq. (11) is of the same order of magnitude. Therefore, the uncertainty on the shape of cylinders (and on the diameter) should be decreased in priority in order to get a better control of the biosensor efficiency. This improvement is critical for cylinders with smaller height.
The present control on the thickness of gold deposition is about ±2 nm and that of diameters is about ±20 nm. In this case, the uncertainty on the LSPR position remains lower than 35 nm for all diameters if h ∈ [10; 70] nm (Fig. 11). The relative uncertainty is about two times greater for small diameters and the absolute uncertainty decreases slightly as h increases.
Figure 11 show that the tolerance on the small geometrical parameters (D,h) does hardly differ from that on bigger ones. Therefore, the whole process of fabrication, whatever is the LSPR position, will take advantage of the improvement of the lateral control of metal deposition.
In this section, we have obtained an heuristic law to describe the link between the position of the LSPR and the size parameters D and h of the cylinders. This law seems to be valid even if an adhesion layer of chromium of thickness e = 2 − 6 nm is used. Moreover, the simplicity of this law helps to determine a first approximation of the size of the cylinder for tuning the LSPR position, as well as the effect of the propagation of experimental uncertainties on the position of the LSPR.
The Discrete Dipole Approximation (DDA) is used for a parametric study of the biosensors made of a grating of nanocylinders. The Localized Surface Plasmon Resonance (LSPR) measurement is modeled by the maximum of the extinction cross-section over the considered spectrum. Considering a fixed distance between cylinders, the investigated parameters are the height h, the diameter D, the thickness e of the chromium adhesion layer, and the roughness of the nanocylinders. Thin adhesion layers slightly modify the position of the LSPR. Roughness induces a redshift which enables to fit experimental results despite the use of bulk permittivities for chromium and gold and an effective index model for the system substrate-air. The relative influence of h and D is more complex but can be deduced from an heuristic law for the LSPR position. This law is obtained through an affine fitting of the proposed numerical experience plan. The agreement with experimental results [4, 8] is satisfactory, falling within the experimental uncertainties of fabrication. Therefore the heuristic law of behavior of the LSPR position can be used with confidence. Then the reciprocal function of the position of the LSPR can be used to a first computation of class of diameters and heights of cylinders to design sensors. This approach could be extended to more complex shape of nanoparticles, at the expense of computation time and complexity of interpretation. The propagation of uncertainties of fabrication being determined for the investigated parameters, the influence of the functionalization layer that is used to fix the bio-molecules of interest in the vicinity of metallic nanoparticles will be the object of further studies. Higher order fits should also be investigated, at the possible expense of the uniqueness and simplicity of the solution of the inverse problem.
This study is partially supported by the Conseil Régional de Champagne-Ardennes, the Conseil Général de l’Aube, and the Nanoantenna European Project (FP7 Health-F5-2009-241818).
References and links
1. E. C. Le Ru and P. G. Etchegoin, Principles of sSurface-Enhanced Raman Spectroscopy and Related Plasmonic Effects (Elsevier, Amsterdam, 2009).
2. M. Vidotti, R. F. Carvalhal, R. K. Mendes, D. C. M. Ferreira, and L. T. Kubota, “Biosensors based on gold nanostructures,” J. Braz. Chem. Soc. 22, 3–20 (2011). [CrossRef]
3. S. A. Maier, Plasmonics. Fundamentals and Applications (Springer, New York, USA, 2007).
4. J. Grand, M. Lamy de la Chapelle, J.-L. Bijeon, P.-M. Adam, A. Vial, and P. Royer, “Role of localized surface plasmons in surface-enhanced Raman scattering of shape-controlled metallic particles in regular arrays,” Phys. Rev. B 72, 033407 (2005). [CrossRef]
5. N. Félidj, J. Aubard, G. Lévi, J. R. Krenn, M. Salerno, G. Schider, B. Lamprecht, A. Leitner, and F. R. Aussenegg, “Controlling the optical response of regular arrays of gold particles for surface-enhanced Raman scattering,” Phys. Rev. B 65, 075419–075427 (2002). [CrossRef]
6. N. Félidj, J. Aubard, G. Lévi, J. R. Krenn, A. Hohenau, G. Schider, A. Leitner, and F. R. Aussenegg, “Optimized surface-enhanced Raman scattering on gold nanoparticles arrays,” Appl. Phys. Lett. 82, 3095–3097 (2003). [CrossRef]
7. A.-S. Grimault, A. Vial, and M. Lamy de la Chapelle, “Modeling of regular gold nanostructures arrays for SERS applications using a 3D FDTD method,” Appl. Phys. B-Lasers Opt. 84, 111–115 (2006). [CrossRef]
8. N. Guillot, H. Shen, B. Frémaux, O. Péron, E. Rinnert, T. Toury, and M. Lamy de la Chapelle, “Surface enhanced Raman scattering optimization of gold nanocylinder arrays: influence of the localized surface plasmon resonance and excitation wavelength,” Appl. Phys. Lett. 97, 023113–023116 (2010). [CrossRef]
9. H.-H. Yan, Y.-Y. Xiao, S.-X. Xie, and H.-J. Li, “Tunable plasmon resonance of a touching gold cylinder arrays,” J. At. Mol. Sci. 3, 252–261 (2012).
11. B. Lamprecht, G. Schider, R. T. Lechner, H. Diltbacher, J. R. Krenn, A. Leitner, and F. R. Aussenegg, “Metal nanoparticles gratings: influence of dipolar interaction on the plasmon resonance,” Phys. Rev. Lett. 84, 4721–4723 (2000). [CrossRef] [PubMed]
12. S. Davy, D. Barchiesi, M. Spajer, and D. Courjon, “Spectroscopic study of resonant dielectric structures in near–field,” Eur. Phys. J.-Appl. Phys. , 5, 277–281 (1999). [CrossRef]
13. D. Barchiesi, “Pseudo modulation transfer function in reflection scanning near-field optical microscopy,” Opt. Commun. 154, 167–172 (1998). [CrossRef]
14. J. Grand, Plasmons de surface de nanoparticules : spectroscopie d’extinction en champs proche et lointain, diffusion Raman exaltée, Ph.D. thesis (Université de technologie de Troyes, 2004). [PubMed]
15. D. Barchiesi, D. Macías, L. Belmar-Letellier, D. Van Labeke, M. Lamy de la Chapelle, T. Toury, E. Kremer, L. Moreau, and T. Grosges, “Plasmonics: influence of the intermediate (or stick) layer on the efficiency of sensors,” Appl. Phys. B-Lasers Opt. 93, 177–181 (2008). [CrossRef]
16. S. Kessentini and D. Barchiesi, “Roughness effect on the efficiency of dimer antenna based biosensor,” Advanced Electromagnetics (AEM) 1, 41–47 (2012).
17. L. Billot, M. Lamy de la Chapelle, A. S. Grimault, A. Vial, D. Barchiesi, J.-L. Bijeon, P.-M. Adam, and P. Royer, “Surface enhanced Raman scattering on gold nanowire arrays: evidence of strong multipolar surface plasmon resonance enhancement,” Chem. Phys. Lett. 422, 303–307 (2006). [CrossRef]
18. M. Pelton, J. Aizpurua, and G. W. Bryant, “Metal-nanoparticles plasmonics,” Laser & Photon. Rev. 2, 136–159 (2008). [CrossRef]
19. D. Sharma, R. Sharma, S. Dua, and V. N. Ojha, “Pitch measurements of 1D/2D gratings using optical profiler and comparison with SEM /AFM,” in AdMet 2012, (Metrology Society of India, ARAI, Pune, India, 2012), NM 003, 1–4.
20. G. Laurent, N. Félidj, J. Aubard, G. Lévi, J. R. Krenn, A. Hohenau, G. Schider, A. Leitner, and F. R. Aussenegg, “Evidence of multipolar excitations in surface enhanced Raman scattering,” Phys. Rev. B 65, 045430 (2005). [CrossRef]
21. D. Barchiesi, E. Kremer, V. Mai, and T. Grosges, “A Poincaré’s approach for plasmonics: the plasmon localization,” J. Microscopy 229, 525–532 (2008). [CrossRef]
22. C. F. Bohren and D. R. Huffman, Absorption and Scattering of Light by Small Particles (John Wiley & Sons, Inc., New York, 1998). [CrossRef]
23. A. A. Yanik, M. Huang, A. Artar, T.-Y. Chang, and H. Altug, “On-chip nanoplasmonic biosensors with actively controlled nanofluidic surface delivery,” in Plasmonics: metallic nanostructures and their optical properties VIII, M. I. Stockman, ed. (SPIE, San Diego, California, USA, 2010), vol. 7757, 775735. [CrossRef]
24. X. Huang, S. Neretina, and M. A. El-Sayed, “Gold nanorods: from synthesis and properties to biological and biomedical applications,” J. Adv. Mater. 21, 4880–4910 (2009). [CrossRef]
25. Y. B. Zheng, B. K. Juluri, X. Mao, T. R. Walker, and T. J. Huang, “Systematic investigation of localized surface plasmon resonance of long-range ordered Au nanodisk arrays,” J. Appl. Phys 103, 014308 (2008). [CrossRef]
26. H. Shen, N. Guillot, J. Rouxel, M. Lamy de la Chapelle, and T. Toury, “Optimized plasmonic nanostructures for improved sensing activities,” Opt. Express 20, 21278–21290 (2012). [CrossRef] [PubMed]
27. A. Vial and T. Laroche, “Description of dispersion properties of metals by means of the critical points model and application to the study of resonant structures using the FDTD method,” J. Phys. D. 40, 7152–7158 (2007). [CrossRef]
28. D. Barchiesi, N. Lidgi-Guigui, and M. Lamy de la Chapelle, “Functionalization layer influence on the sensitivity of surface plasmon resonance (SPR) biosensor,” Opt. Commun. 285, 1619–1623 (2012). [CrossRef]
29. D. Barchiesi, New perspectives in biosensors technology and applications (INTECH Open Access, Rijeka, Croatia, 2011), chap. 5, pp. 105–126.
30. H. Aouani, J. Wenger, D. Gérard, H. Rigneault, E. Devaux, T. W. Ebbesen, F. Mahdavi, T. Xu, and S. Blair, “Crucial role of the adhesion layer on the plasmonic fluorescence enhancement,” ACS Nano 3, 2043–2048 (2009). [CrossRef] [PubMed]
31. F. D. Hastings, J. B. Schneider, and S. L. Broschat, “A Monte-Carlo FDTD technique for rough surface scattering,” IEEE Transactions on antennas and propagation 43, 1183–1191 (1995).
32. K. M. Byun, S. J. Yoon, D. Kim, and S. J. Kim, “Sensitivity analysis of a nanowire-based surface plasmon resonance biosensor in the presence of surface roughness,” J. Opt. Soc. Am. A 24, 522–529 (2007). [CrossRef]
33. V. Poroshin, Y. Borovin, and D. Bogomolov, “Transfer of the surface roughness geometry into the universal FEM software ANSYS,” Advanced Engineering 3, 1846–5900 (2009).
34. A. Kato, S. Burger, and F. Scholze, “Analytical modeling and three-dimensional finite element simulation in line edge roughness in scatterometry,” Appl. Opt. 51, 6457–6464 (2012). [CrossRef] [PubMed]
35. A. Trügler, J.-C. Tinguely, J. R. Krenn, A. Hohenau, and U. Hohenester, “Influence of surface roughness on the optical properties of plasmonic nanoparticles,” Phys. Rev. B 83, 081412 (2011). [CrossRef]
36. B. T. Draine and P. J. Flatau, “Discrete-dipole approximation for scattering calculations,” J. Opt. Soc. Am. A 11, 1491–1499 (1994). [CrossRef]
37. N. Félidj, J. Aubard, and G. Lévi, “Discrete dipole approximation for ultraviolet-visible extinction spectra simulation of silver and gold colloids,” J. Chem. Phys 111, 1195–1208 (1999). [CrossRef]
38. K. L. Kelly, E. Coronado, L. L. Zhao, and G. C. Schatz, “The optical properties of metal nanoparticles: the influence of size, shape, and dielectric environment,” J. Phys. Chem. B 107, 668–677 (2003). [CrossRef]
39. K. S. Lee and M. A. El-Sayed, “Dependence of the enhanced optical scattering efficiency relative to that of absorption of gold metal nanorods on aspect ratio, size, end-cap shape, and medium refractive,” J. Phys. Chem. B 109, 20331–20338 (2005). [CrossRef]
40. P. K. Jain, K. S. Lee, I. H. El-Sayed, and M. A. El-Sayed, “Calculated absorption and scattering properties of gold nanoparticles of different size, shape, and composition: applications in biological imaging and biomedicine,” J. Phys. Chem. 110, 7238–7248 (2006). [CrossRef]
41. B. T. Draine and P. J. Flatau, “Discrete-dipole approximation for periodic targets: theory and tests,” J. Opt. Soc. Am. A 25, 2693–2703 (2008). [CrossRef]
42. S. Kessentini and D. Barchiesi, “Quantitative comparison of optimized nanorods, nanoshells and hollow nanospheres for photothermal therapy,” Biomed. Opt. Express 3, 590–604 (2012). [CrossRef] [PubMed]
43. H. Devoe, “Optical properties of molecular aggregates. I. Classical model of electronic absorption and refraction,” J. Chem. Phys. 41, 393–400 (1964). [CrossRef]
44. H. Devoe, “Optical properties of molecular aggregates. II. Classical theory of the refraction, absorption, and optical activity of solutions and crystals,” J. Chem. Phys. 43, 3199–3208 (1965). [CrossRef]
45. E. Purcell and C. R. Pennypacker, “Scattering and absorption of light by nonspherical dielectric grains,” Astrophys. J. 186, 705–714 (1973). [CrossRef]
46. V. A. Markel, “Scattering of light from two interacting spherical particles,” J. Mod. Opt. 39, 853–861 (1992). [CrossRef]
47. P. C. Chaumet, A. Rahmani, and G. W. Bryant, “Generalization of the coupled dipole method to periodic structures,” Phys. Rev. B 67, 165404(1–5) (2003). [CrossRef]
48. E. Zubko, D. Petrov, Y. Grynko, Y. Shkuratov, H. Okamotot, K. Muinonen, T. Nousiainen, H. Kimura, T. Yamamoto, and G. Videen, “Validity criteria of the discrete dipole approximation,” Appl. Opt. 49, 1267–1279 (2010). [CrossRef] [PubMed]
49. C. Ungureanu, R. G. Rayavarapu, S. Manohar, and T. G. Van Leeuwen, “Discrete dipole approximation simulations of gold nanorod optical properties: choice of input parameters and comparison with experiment,” J. Appl. Phys. 105, 102032–102039 (2009). [CrossRef]
50. W.-H. Yang, G. C. Schatz, and R. P. Van Duyne, “Discrete dipole approximation for calculating extinction and Raman intensities for small particles with arbitrary shapes,” J. Chem. Phys. 193, 869–875 (1995). [CrossRef]
51. H. Parviainen and K. Lumme, “Scattering from rough thin films: discrete-dipole-approximation simulations,” J. Opt. Soc. Am. A 25, 90–97 (2008). [CrossRef]
52. B. T. Draine and P. J. Flatau, “User guide to the discrete dipole approximation code DDSCAT 7.1,” http://arXiv.org/abs/1002.1505v1 (2010).
53. A. J. Haija, W. L. Freeman, and T. Roarty, “Effective characteristic matrix of ultrathin multilayer structures,” Opt. Appl. 36, 39–50 (2006).
54. A. J. Abu El-Haija, “Effective medium approximation for the effective optical constants of a bilayer and a multilayer structure based on the characteristic matrix technique,” J. Appl. Phys. 93, 2590–2594 (2003). [CrossRef]
56. P. Johnson and R. W. Christy, “Optical constants of the noble metals,” Phys. Rev. B 6, 4370 (1972). [CrossRef]
57. E. D. Palik, Handbook of Optical Constants (Academic Press Inc., San Diego USA, 1985).
58. S. Ekgasit, C. Thammacharoen, F. Yu, and W. Knoll, “Influence of the metal film thickness on the sensitivity of surface plasmon resonance biosensors,” Appl. Spectrosc. 59, 661–667 (2005). [CrossRef] [PubMed]
59. H. Neff, W. Zong, A. Lima, M. Borre, and G. Holzhüter, “Optical properties and instrumental performance of thin gold films near the surface plasmon resonance,” Thin Solid Films 496, 688–697 (2006). [CrossRef]
60. B. A. Sexton, B. N. Feltis, and T. J. Davis, “Effect of surface roughness on the extinction-based localized surface plasmon resonance biosensor,” Sens. Actuator A-Phys. 141, 471475 (2008).
61. Working Group 1, Evaluation of measurement data - Guide to the expression of uncertainty in measurement, (Joint Committee for Guides in Metrology, Paris, 1st ed., 2008, Corrected version 2010).
62. D. Macías, A. Vial, and D. Barchiesi, “Application of evolution strategies for the solution of an inverse problem in Near-Field Optics,” J. Opt. Soc. Am. A 21, 1465–1471 (2004). [CrossRef]
63. T. Grosges, D. Barchiesi, T. Toury, and G. Gréhan, “Design of nanostructures for imaging and biomedical applications by plasmonic optimization,” Opt. Lett. 33, 2812–2814 (2008). [CrossRef] [PubMed]
64. D. Macías, A. Vial, and D. Barchiesi, “Evolution strategies approach for the solution of an inverse problem in near-field optics,” in Lecture notes in computer science (6e European Workshop on Evolutionary Computation in Image Analysis and Signal Processing), vol. 3005 / 2004, G. Raidl, S. Cagnoni, J. Branke, R. Corne, D. W. Drechsler, Y. Jin, C. Johnson, P. Machado, E. Marchiori, F. Rothlauf, G. Smith, and G. Squillero, eds. (Springer-VerlagHeidelberg, Germany, 2004), 329 –338.
65. D. Barchiesi and T. Grosges, “Measurement of the decay lengths of the near field signal in tapping mode,” Curr. Appl. Phys. 9, 1227–1231 (2009). [CrossRef]
66. D. Barchiesi, O. Bergossi, M. Spajer, and C. Pieralli, “Image resolution in reflection scanning near-field optical microscopy (R-SNOM) using shear-force (ShF) feedback: characterization using spline and Fourier spectrum,” Appl. Opt. 36, 2171–2177 (1997). [CrossRef] [PubMed]
67. T. Grosges, D. Barchiesi, S. Kessentini, G. Gréhan, and M. Lamy de la Chapelle, “Nanoshells for photothermal therapy: a Monte-Carlo based numerical study of their design tolerance,” Biomed. Opt. Express 2, 1584–1596 (2011). [CrossRef] [PubMed]
68. K. J. Prashant, X. Huang, I. H. El-Sayed, and M. A. El-Sayed, “Calculated absorption and scattering properties of gold nanoparticles of different size, shape and composition: Application in biological imaging and biomedicine,” Accounts Chem. Res. 41, 1578–1586 (2008).