Abstract

A spatial heterodyne Raman spectrometer (SHRS), constructed using a modular optical cage and lens tube system, is described for use with a commercial silica and a custom single-crystal (SC) sapphire fiber Raman probe. The utility of these fiber-coupled SHRS chemical sensors is demonstrated using 532 nm laser excitation for acquiring Raman measurements of solid (sulfur) and liquid (cyclohexane) Raman standards as well as real-world, plastic-bonded explosives (PBX) comprising 1,3,5- triamino- 2,4,6- trinitrobenzene (TATB) and octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX) energetic materials. The SHRS is a fixed grating-based dispersive interferometer equipped with an array detector. Each Raman spectrum was extracted from its corresponding fringe image (i.e., interferogram) using a Fourier transform method. Raman measurements were acquired with the SHRS Littrow wavelength set at the laser excitation wavelength over a spectral range of ∼1750 cm⁻¹ with a spectral resolution of ∼8 cm⁻¹ for sapphire and ∼10 cm⁻¹ for silica fiber probes. The large aperture of the SHRS allows much larger fiber diameters to be used without degrading spectral resolution as demonstrated with the larger sapphire collection fiber diameter (330 μm) compared to the silica fiber (100 μm). Unlike the dual silica fiber Raman probe, the dual sapphire fiber Raman probe did not include filtering at the fiber probe tip nearest the sample. Even so, SC sapphire fiber probe measurements produced less background than silica fibers allowing Raman measurements as close as ∼85 cm⁻¹ to the excitation laser. Despite the short lengths of sapphire fiber used to construct the sapphire probe, well-defined, sharp sapphire Raman bands at 420, 580, and 750 cm⁻¹ were observed in the SHRS spectra of cyclohexane and the highly fluorescent HMX-based PBX. SHRS measurements of the latter produced low background interference in the extracted Raman spectrum because the broad band fluorescence (i.e., a direct current, or DC, component) does not contribute to the interferogram intensity (i.e., the alternating current, or AC, component). SHRS spectral resolution, throughput, and signal-to-noise ratio are also discussed along with the merits of using sapphire Raman bands as internal performance references and as internal wavelength calibration standards in Raman measurements.

© 2019 The Author(s)

Backscattering Raman spectroscopy using multi-grating spatial heterodyne Raman spectrometer

Jianli Liu, Bayanheshig, Xiangdong Qi, Shanwen Zhang, Ci Sun, Jiwei Zhu, Jicheng Cui, and Xiaotian Li
Appl. Opt. 57(33) 9735-9745 (2018)

Broadband transmission Raman measurements using a field-widened spatial heterodyne Raman spectrometer with mosaic grating structure

Jun Qiu, Xiangdong Qi, Xiaotian Li, Yuguo Tang, Jiriga Lantu, Xiaotao Mi, and Heshig Bayan
Opt. Express 26(20) 26106-26119 (2018)

Development of a spatial heterodyne Raman spectrometer with echelle-mirror structure

Jun Qiu, Xiangdong Qi, Xiaotian Li, Zhenyu Ma, Jirigalantu, Yuguo Tang, Xiaotao Mi, Xiaoming Zheng, Rui Zhang, and Bayanheshig
Opt. Express 26(9) 11994-12006 (2018)

Broadband, high-resolution Raman observations from a double-echelle spatial heterodyne Raman spectrometer

Jun Qiu, Xiangdong Qi, Xiaotian Li, Wenhui Xu, Yuguo Tang, Zhenyu Ma, and Bayanheshig
Appl. Opt. 57(30) 8936-8941 (2018)

In situ surface-enhanced Raman scattering sensing with soft and flexible polymer optical fiber probes

Jingjing Guo, Yuqing Luo, Changxi Yang, and Lingjie Kong
Opt. Lett. 43(21) 5443-5446 (2018)